Epson EL Series Скачать руководство пользователя страница 208

Страница: 208 / 236

11. Calibration

Part 2: Maintenance

196

(17) Display the number of pulses in this position using the PULSE command and check

that they match the values obtained in step (12) on previous page.

PULSE

16000 10000

' Axes #1 and #2 pulses.

0 -10

' Axes #3 and #4 pulses.

(18) Use the SLOCK command to put the free axes back under servo control.

SLOCK 1,3

' Axis #1 and #3 are under servo control.

(19) Move to another teach point and check the position.

Accurate calibration of Axis #2

For accurate calibration of Axis #2, calculation of robot working point coordinates is most
important in the following cases.

Entering coordinate values to teach a point.

Switching the arm orientation between right and left at a given point.

Using the PALET command.

During CP control (such as liner or circular interpolation).

Using the LOCAL command.

For statements using relative coordinates. < Example,

P1+X100

If the methods above require accuracy of Axis #2, then calibrate for both right and left arm
orientations. Note that this method cannot be used if Axis #4 has excessive run-out.

(1) Display HOFS values using the HOFS command and note values [A], [B], [C], and

[D].

> HOFS

[A] [B]

' HOFS values for Axes #1 and #2.

[C] [D]

' HOFS values for Axes #3 and #4.

(2) Select a point for teaching that is within the region accessible to both right and left arm

and is easy to verify for accuracy. Carry out teaching and call the point P1.

P1=P*

(3) Display the number of pulses at the P1 position using the PULSE command. Note the

Axis #2 value

[F1]

> PULSE

[E] [F1]

' Axes #1 and #2 pulses.

[G] [H]

' Axes #3 and #4 pulses.

Содержание EL Series












































































































































































































































Результаты поиска

Содержание EL Series

Отзывы:

Похожие инструкции для EL Series

Бренды по названию

Популярные бренды

Epson EL Series, Руководство манипулятора

Результаты поиска

Содержание EL Series

Отзывы:

Похожие инструкции для EL Series

Бренды по названию

Популярные бренды