ePropulsion Side Mount Control Скачать руководство пользователя страница 40

Страница: 40 / 48

Code

Cause

Solution

E20

Battery

Communication

Fault

Please check whether the version of Side Mount
Control corresponds to the motor version first.
If not, please refer to

2.4 Version Setting for

version switching.
If the version is correct, turn off the motor and
reconnect the battery cable. If this issue cannot
be solved, please contact your dealer.

E21

Motor

Communication

Fault

Turn off the motor and reconnect the battery
cable. If this issue cannot be solved please
contact your dealer.

E30

Throttle

Calibration

Required

Please refer to section

4.2.2 Recalibration

recalibrate the throttle position sensor.

E51

Battery

Charging

Temperature

Fault

Make sure the environment temperature is
within 0°C to 45°C. Charging will continue when
cell temperature is in that range.

E54

Battery

Discharging

Temperature

Fault

Detach the battery and contact your dealer.

E55

Battery Pack

Over Voltage

Stop the motor and wait until the error message
disappears. If the problem persists, contact your
dealer for repair.

E56

Battery Empty

Indicating the battery is empty. The motor can
probably be restarted at lower speed after the
message is dismissed.

E57

Battery

Charging Over

Current

Please contact your dealer.

Содержание Side Mount Control
















































Результаты поиска

Содержание Side Mount Control

Отзывы:

Похожие инструкции для Side Mount Control

Бренды по названию

Популярные бренды

ePropulsion Side Mount Control, Руководство пользователя

Результаты поиска

Содержание Side Mount Control

Отзывы:

Похожие инструкции для Side Mount Control

Бренды по названию

Популярные бренды