ePropulsion Side Mount Control Скачать руководство пользователя страница 42

Страница: 42 / 48

Code

Cause

Solution

E10

Motor stall, which may
be caused by blocked
propeller

Turn off power, then clean up the things
winding around the propeller. Test if the
propeller can be rotated by hand before
operation.

E11

The temperature of
motor is too high.

Stop operating the motor and wait until
the temperature falls within the normal
operating temperature range.

E12

The temperature of
circuit board is too
high.

Stop operating the motor and wait until
the temperature falls within the normal
operating temperature range.

E15

Failure was found
in the circuit board
temperature sensors.

Try to turn off the main power switch
and wait for 10 seconds then turn on the
switch again.

E16

Calibration
Abnormality of Current
Sensor

Please contact the dealer for help.

E21

Driver Communication
Fault

Please check whether the version of
Side Mount Control corresponds to the

motor version first. If not, please refer to

2.4 Version Setting for version switching.

If the version is correct, check the
communication cable connection and
restart the motor. If the problem still
arises, please contact the ePropulsion
authorized dealer for assistance.

E22

MCU Communication
Abnormality

Please restart to see if the error
disappears, if not, please contact your
dear for help.

Содержание Side Mount Control
















































Результаты поиска

Содержание Side Mount Control

Отзывы:

Похожие инструкции для Side Mount Control

Бренды по названию

Популярные бренды

ePropulsion Side Mount Control, Руководство пользователя

Результаты поиска

Содержание Side Mount Control

Отзывы:

Похожие инструкции для Side Mount Control

Бренды по названию

Популярные бренды