ePropulsion Side Mount Control Скачать руководство пользователя страница 41

Страница: 41 / 48

Code

Cause

Solution

E58

Battery

Discharging

Over Current

Please contact your dealer.

E59

Battery

Hardware Fault

Battery has encountered serious hardware
breakdown. Please replace the battery and
contact your dealer.

Other

Battery Cell

Fault

Battery cell fault occurs, please replace the
battery and contact your dealer to repair the
problematic battery.

If the problem persists, please consult your ePropulsion authorized
dealer for assistance.

b.Warning M

ssages (Navy3.0, Navy6.0 & Pod3.0 Version)

The following error codes and solutions are applicable only to NAVY 3.0,

NAVY 6.0 outboard motor and Pod Drive 3.0.

Code

Cause

Solution

E01

Battery voltage is over
the operating range.

Replace a battery based on suggested

operation specifications.

E02

Propeller may be
blocked, causing
motor overcurrent

Please refer to the solution to E10.

Motor fails or circuit
board fails causing
motor overcurrent

Try to turn off the main power switch
and wait for 10 seconds then turn on the
switch again.

E06

The battery voltage
level is too low.

Operate the motor at low power. Please
charge the battery as soon as possible.

Содержание Side Mount Control
















































Результаты поиска

Содержание Side Mount Control

Отзывы:

Похожие инструкции для Side Mount Control

Бренды по названию

Популярные бренды

ePropulsion Side Mount Control, Руководство пользователя

Результаты поиска

Содержание Side Mount Control

Отзывы:

Похожие инструкции для Side Mount Control

Бренды по названию

Популярные бренды