Epiphone Baby Will Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 36

background image

http://www.GuitarAmplifierPCBs.com

“Baby Will” Valve Junior Conversion

Version 4

Build Manual

22 September 2009

11 of 36

5.2.4 Remove the Volume Potentiometer

Unscrew the fastening nut from the volume
potentiometer.

Pull the volume pot back into the chassis. Leave it
connected to the stock EVJ circuit board.

The volume pot will be glued to the
chassis. This part will NOT be used later
in the build, so use whatever force you
need.

5.2.5 Remove the Stock EVJ Circuit Board

Disconnect these four (4) leads from
the stock EVJ circuit board.

Lift the ground wire from the star
ground post.

Unplug the input jack wire at the circuit
board.

Remove the six (6) screws fastening
the circuit board to the chassis.

«
...
9
10
11
12
13
...
»

Содержание Baby Will





































Отзывы:

Нет отзывов

Похожие инструкции для Baby Will

Бренд: Jet City Страницы: 6

Bassman Bassman 100

Бренд: Fender Страницы: 20

Бренд: Fender Страницы: 156

G-DEC 3 Thirty & Fifteen

Бренд: Fender Страницы: 24

Бренд: Takstar Страницы: 2

Бренд: Takstar Страницы: 2

Бренд: TAD Страницы: 77

Бренд: NAD Страницы: 18

Boston GT GT-5750

Бренд: Boston Acoustics Страницы: 12

Metaltronix M-1000P

Бренд: Lee Jackson Страницы: 3

Бренд: Klipsch Страницы: 10

Бренд: Kicker Страницы: 20

Бренд: Ocean Matrix Страницы: 3

Бренд: Art Страницы: 25

Бренд: Harman Kardon Страницы: 22

Бренд: ONSIA Страницы: 7

Бренд: Parker Страницы: 8

Бренд: Power Acoustik Страницы: 11

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды