EPIGY TECHNOLOGIES QUADRO 2XI Скачать руководство пользователя страница 8

Страница: 8 / 63

Quadro Manual I: Installation Guide

Requirements

Quadro2x, 2xi; Quadro4x, 4xi; Quadro16x, 16xi (SW Version 5.3.x)

Requirements

•

One 120/240 VAC power outlet in close proximity to the Quadro.

•

One RJ45 Ethernet 10/100 broadband Internet connection.

•

At least one RJ11 telephone connection is recommended to connect the Quadro to
the PSTN network (all Quadro IP PBXs with FXO ports). For ISDN Quadros an RJ45
CAT 5 cable is needed to connect Quadro to ISDN.

•

At least one off-the-shelf analog phone with an RJ11 telephone cable.

•

One CAT 5 Ethernet cable with an RJ45 connector to connect to the Quadro LAN port.

•

One PC with a 10/100 Mbps Ethernet card or adapter installed.

•

TCP/IP network protocol installed on each PC.

•

For optimal results, Internet Explorer 5.5 or higher, or Netscape Navigator 4.7 or high-
er are recommended.

Please Note:

All Quadro IP PBXs are shipped with one RJ11 cable and one straight RJ45

CAT 5 cable. If the LAN connector of the Quadro connects to a hub or switch, a crossover
cable may be required.

Other cables are added according to the different connectivity requirements of the Quadro
IP PBX types.

Содержание QUADRO 2XI
































































Результаты поиска

Содержание QUADRO 2XI

Отзывы:

Похожие инструкции для QUADRO 2XI

Бренды по названию

Популярные бренды

EPIGY TECHNOLOGIES QUADRO 2XI, Руководство по установке

Результаты поиска

Содержание QUADRO 2XI

Отзывы:

Похожие инструкции для QUADRO 2XI

Бренды по названию

Популярные бренды