background image

1

 

energiSava

®

 500

SHOULD YOU ENCOUNTER ANY PROBLEMS INSTALLING 
THIS UNIT, CALL US ON: 

0345 27 27 810

Safety

Important: Read these instructions fully before the installation of this appliance

1.  Installation of the appliance and accessories 

must be carried out by a qualified and 

suitable competent person and be carried 

out in clean, dry conditions where dust and 

humidity are at minimal levels.

2.  This manual covers the installation of the 

Heat Recovery Ventilation unit.

3.  All wiring must conform to current I.E.E. 

Wiring Regulations and all applicable 

standards and Building Regulations.

4.  Inspect the appliance and electrical supply 

cord. If the supply cord is damaged, it must 

be replaced by the manufacturer, their 

service agent or similarly qualified persons 

in order to avoid a hazard.

5.  The unit is supplied with a mains rated 3 

core flexible cord (PVC sheathed, brown, 

blue and green/yellow 0.75mm²).

6.  The appliance must be connected to a 

local double pole isolation switch with a 

contact separation of at least 3mm.

7.  The appliance must be earthed.

8.  The unit is suitable for 230V ~ 50/60Hz 

single phase with a fuse rating of 5A.

9.  Status indicator, control & communication 

cable access is via the fitted cable gland(s) 

which are suitable for Ø3- 6mm cable.

10.  Status indicator, control & communication 

cable - Unshielded 4 Core 18-24AWG 

Stranded, Tinned Copper.

11.  Control & communication cables should 

not be placed within 50mm or on the same 

metal cable tray as any 230V~ lighting or 

power cables.

12.  Ensure all cable glands are fully tightened.

13.  The unit must be stored in a clean and dry 

environment.  Do not install the appliance 

in areas where the following may be 

present or occur; 

•  Excessive oil or a grease laden 

atmosphere.

•  Corrosive or flammable gases, liquids or 

vapours.

•  Ambient temperatures above 40°C or 

below -5°C.

•  Humidity levels above 90% or is a wet 

environment.

14.  The appliance is not suitable for installation 

to the exterior of the dwelling.

15.  This appliance can be used by children 

aged from 8 years and above and persons 

with reduced physical, sensory or mental 

capabilities or lack of experience and 

knowledge if they have been given 

supervision or instruction concerning 

use of the appliance in a safe way and 

understand the hazards involved. Children 

should be supervised to ensure that they 

do not play with the appliance. Cleaning 

and user maintenance shall not be made 

by children without supervision.

16.  Ensure that external grilles are located 

away from any flue outlet, in accordance 

with relevant Building Regulations.

17.  The unit must not be connected to a tumble 

dryer or a cooker hood.

18.  Precautions must be taken to avoid the 

back-flow of gases into the room from an 

open flue appliance.

19.  Ensure all ducting, condensate drain and 

associated pipe work is free from debris and 

blockages before switching on the unit.

Содержание energiSava 500





















Отзывы: