Environnement AF22e Скачать руководство пользователя страница 83

Страница: 83 / 118

Duplication prohibited

AF22e

Environnement

S.A

APRIL 2016

4–3

4 PREVENTIVE

MAINTENANCE

4.1 SAFETY

INSTRUCTIONS

The user must follow these safety instructions at all times:

−

Always turn off the power supply when performing analyzer maintenance.

−

Personnel should be trained in the proper operation of this equipment before attempting to operate it.

−

The manufacturer shall not be responsible for any adverse outcomes resulting from the following:

•

Use of the monitor by unqualified service personnel.

•

Use of the monitor under conditions other than those specified in this document.

•

Use of components or accessories not manufactured by Environnement

S.A,

failure to use

recommended parts may reduce the safety features.

•

Use of this equipment in a manner not approved by Environnement

S.A,

as it can cause harm to

the equipment or operating personnel.

•

Inappropriate maintenance of the analyzer.

−

A periodic inspection is required.

Содержание AF22e























































































































Результаты поиска

Содержание AF22e

Отзывы:

Environnement AF22e, Техническое руководство, Страница: 83 / 118

Результаты поиска

Содержание AF22e

Отзывы: