background image

 

 

2

SAFETY PRECAUTIONS 

FOR SAFE INSTALLATION AND OPERATION OF YOUR "ENVIRO" STOVE, PLEASE, 

CAREFULLY READ THE FOLLOWING INFORMATION: 

 

GENERAL 

• 

Installation and repair should be done by a 

qualified service person. The appliance should 
be inspected before use and at least once per 
year by a qualified service person. More 
frequent cleaning may be required due to 
excessive lint from carpeting, bedding material, 
etc.  It is imperative that control compartments, 
burners and circulating air passageways of the 
appliance be kept clean. 
 

• 

Due to high temperatures the appliance 

should be located out of high traffic areas and 
away from furniture and draperies. 
Children and adults should be alerted to 
hazards of high surface temperatures and 
should stay away to avoid burns or clothing 
ignition. 
 

• 

Young children should be carefully 

supervised when they are in the same room as 
the appliance.   
 

• 

Clothing or other flammable material should 

not be placed on or near the appliance.   

 

• 

All "ENVIRO" gas-fired appliances must be 

installed in accordance with these instructions.  
Carefully read all the instructions in this manual first.  
Consult the building authority having jurisdiction to 
determine the need for a permit prior to commencing 
the installation. 
 

• 

NOTE 

Failure to follow these instructions could 

cause a malfunction of the fireplace, which could 
result in death, serious bodily injury, and/or property 
damage.   
 

• 

Failure to follow these instructions may also void 

your fire insurance and/or warranty. 
 

FOR YOUR SAFETY:

 

• 

Installation and service. Must be performed by a 

qualified installer, service agent, or gas supplier. 

• 

Installation must conform to local codes or, in 

the absence of local codes with the current CAN1-B 
149 installation code in Canada or the current 
National Fuel Gas Code ANSI Z223.1 in the USA. 
 

• 

To prevent injuries do not allow anyone who is 
unfamiliar with the operation to use the stove.   

 

• 

Always keep the appliance area clear 

and free of combustible materials, gasoline 
and other flammable vapors and

 

liquids.

   

 

• 

These appliances should not be used as a 

drying rack for clothing or for hanging Christmas 
stockings or decorations. 
 

• 

Due to the paint curing on the stove a faint odor 

and slight smoking will likely be noticed when the 
stove is first used.  Open a window until the slight 
smoking stops. Always connect this gas stove to a 
chimney and vent to the outside of the building 
envelope.  Never vent to another room or inside a 
building. Make sure you use the vent pipe that is 
specified. Make sure that the vent is properly sized 
and is of adequate height to provide the proper draft.  
Inspect the venting system annually for blockage 
and any signs of deterioration. 

 

WARNING:

 Do not operate with 

cracked or broken glass.  Under no 
circumstances should this appliance be 
modified.  Parts that have to be removed 
for servicing must be replaced prior to 
operating this appliance. Only parts 
supplied by Enviro should be used in 
this appliance and replacement should 
only be performed by a licensed or 
qualified service person.  

 

• 

Never use solid fuels such as wood, paper, 

cardboard, coal, or any other flammable liquids etc., 
in this appliance. 
 

• 

Do not use this heater if any part has been 

under water.  Immediately call a qualified service 
technician to inspect the heater and to replace any 
part of the control system and any gas control, which 
has been under water. 
 

• 

Do not abuse glass

 

by striking or slamming door 

shut. 

Содержание EG-40



























Отзывы: