- The user code group 1 is used to release the first lock, and the
user code group 2 is used to release the second lock.
- The user code group 1 and user code group 2 can contain 40
group passwords.
- If the password length exceeds 12 digits, the system will gove out
the sound of “beep,beep,beep,beep”, and the digits you input
before will be cleared at the same time.
- The user code can not be set the same as the master code and
temporary code.
-17-
-16-
• During calling,pressing "cancel" button can cancel the call.
• If input the incorrect access code,the buzzer will give out of beep,beep,beep.a
Input the master code.
(Default : [
1 2 3 4
] +[#] )
(RED)
ON
(BLUE)
OFF
Beep + , Beep
14. Setting the code
for user group 1
15. Setting the code
for user group 2
13. Setting the code
for Temporary 2
12. Setting the code
for Temporary 1
Input the setting code.
18+#
(RED)
ON
(BLUE)
ON
Beep + , Beep
(RED)
ON
(BLUE)
OFF
Beep +
(RED)
ON
(BLUE)
OFF
Beep +
- When input the correct temporary password to release the door,
the system will clear the temporary password after 60 seconds
automatically. But you should know that the password is valid
within 60 seconds after inputing the correct temporary password
- The temporary 1 is used to release the first lock, and the
temporary 2 is used to release the second lock.
- If the password length exceeds 12 digits, the system will give
outof “beep,beep,beep,beep”, and the digits you input be fore will
be cleared at the same time.
- The temporary code can not be set the same as the master code
and user code.
Inputting of code
(ex.: 1006) 1~12 digits
1006 +#
Inputting of code
(ex.: 2011) 1~12 digits
2011 +#
(RED)
ON
(BLUE)
OFF
Beep +
(RED)
OFF
(BLUE)
OFF
Beep + , Beep
(RED)
ON
(BLUE)
OFF
Beep +
Input the setting code.
19+#
(RED)
ON
(BLUE)
ON
Beep + , Beep
Input the setting code.
(ex.:21)
21+#
(RED)
ON
(BLUE)
ON
Beep + , Beep
Input the setting code.
(ex.:60)
60+#
(RED)
ON
(BLUE)
ON
Beep + , Beep
- When the “ * cancel” key is pressed, the LED lights off, the buzzer beeps, and the system exits the setting mode
- When there isn’t any operation in 10s, the LED lights off, the buzzer beeps, and the system exits the setting mode
Inputting of code
(ex.: 2011) 1~12 digits
2011 +#
Inputting of code
(ex.: 2012) 1~12 digits
2012 +#
When the registered user code has been input using the keypad (1~12 digits), the LED indicator
(group 1: red, group 2: blue) lights up, the buzzer sounds,and the electric door strike is unlocked.
• The time interval during which the button must be pressed is approximately 10 seconds.
If the time interval exceeds approximately 10 seconds, the input code will be cleared.
• If you make a mistake when inputting the user code, press the" cancel" button and input the user code again.
• When the "Lockout" function is being activated, the release function is forbidden and the input
operation is disabled for 60 seconds at the 10 continnous incorrect access codes are attemt.
( "Lockout" function: When "Lockout" is activated, the relay 2 doesn't respond the second lock but
responds to the LOCKOUT function. After continuously inputing incorrect access code for 10 times,
LOCKOUT output and the relay 2 will be closed for 60 seconds, the LED-relay 2 will be illuminated for 60
seconds) During this time,the buzzer will continuously sound for about 8 times.
• You can activate the electric door strike by pressing the request to exit button connected to the unit.
Pressing request to exit button 1 releases relay 1, and pressing request to exit button 2 releases relay 2.
(The unlock function will work when the request to exit button is pushed, even while the "Lockout"
function is operating.)
7. Unlock Operations
7.1 Unlocking user code
(RED)
ON
(BLUE)
OFF
Beep +
Red LED lights up
(During relay 1 operation)
Example : Group 1
2011
(RED)
OFF
(BLUE)
ON
Beep +
Red LED lights up
(During relay 2 operation)
Example : Group 2
2012