background image

DFE Module Specifications

A-2 Specifications

7KR4290-02 Ports

Ports 1 and 2

Port interface option slots that support 10GBASE XENPAK 
PHYs. Each port can support a full 10 Gbps throughput with a 
maximum of 20 Gbps, when both ports are active at the same 
time.

Processors/Memory

Processor

IBM 750CXe, 600 MHz processor 

Dynamic Random Access Memory 
(DRAM)

256 MB 

FLASH Memory

32 MB

Physical

Dimensions

46.43 H x 6.05 W x 29.51 D (cm)
18.28 H x 2.38 W x 11.62 D (in.)

Approximate Weight 

7GR4270-12
7GR4202-30
7KR4290-02

Gross: 5.54 kg (12.0 lb) (shipping carton containing one module) 
Net:

4.10 kg (9.0 lb) (one module without packaging)

Approximate Weight 

7GR4280-19

Gross: 5.0 kg (11.0 lb) (shipping carton containing one module) 
Net:

3.86 kg (8.5 lb) (one module without packaging)

Predicted hours for Mean Time 
Between Failures (MTBF) for DFE 
modules:

Refer to the MTBF web site at this URL:

http://www.enterasys.com/support/mtbf/

Environmental

Operating Temperature

5°C to 40°C (41°F to 104°F)

Storage Temperature

-30°C to 73°C (-22°F to 164°F)

Operating Relative Humidity

5% to 90% (non-condensing)

Table A-1 Specifications (continued)

Item

Specification

Содержание Matrix 7GR4202-30























































































Отзывы: