Enterasys IRM2 Скачать руководство пользователя страница 45 | Manualshive

Страница: 45 / 88

background image

Statistics

3-3

Statistics

To open the board-level Statistics window:

1.

Click on the appropriate Board number to display the board menu.

2.

Drag down to Statistics... and release. The board-level Statistics window will
appear.

To access the port-level Statistics window:

1.

Click on the appropriate Port to display the port menu.

2.

Drag down to Statistics... and release. The port-level Statistics window will
appear.

The Board and Port Statistics windows are the same as the Statistics window
displayed in

Figure 3-1

, except that they display statistics applicable to the

selected board or port.

Statistics Defined

The statistics window displays the statistical counts accumulated since the IRM2
was last reset or since the last time the

button was selected. You can

select

at any time to refresh the counters and restart at zero.

The statistics windows display the following information:

Active Users (Available with Release Version 2.00 Firmware and Above)

Displays the number of users (identified by MAC [Ethernet] address)
communicating via a port on the IRM2-managed hub. For an individual port, if
Active Users is greater than one, it indicates that a port is supporting a trunk
connection and will not respond to port locking. Refer to Chapter 4, Source
Address Functions

, in this guide for more information.

Bytes

Displays the total number of bytes (good packets only) that have been processed
by the device, board, or port. Note that this byte count does not include errors.

Broadcasts (Available with Release Version 2.00 Firmware and Above)

Displays the total number of broadcast frames that have been processed by the
device, board, or port. Broadcast packets have a single address recognized by
each station on the net; this address is designated in IP address form as
255.255.255.255, or in MAC hexadecimal form as FF-FF-FF-FF-FF-FF. ARP and
RARP requests sent by bridges and routers are broadcast messages.

Packets

Displays the total number of good packets processed by the device, board, or
port. Again, note that the packet count does not include errors.

«
...
43
44
45
46
47
...
»

Содержание IRM2

























































































Отзывы:

Нет отзывов

Похожие инструкции для IRM2

PM1D Manager V2

Бренд: Yamaha Страницы: 24

DEEP FREEZE ENTERPRISE - PATCH MANAGEMENT...

Бренд: FARONICS Страницы: 23

AUTODESK ROBOT STRUCTURAL ANALYSIS PROFESSIONAL

Бренд: Autodesk Страницы: 6

Phaser 340 Installer

Бренд: Xerox Страницы: 2

Бренд: Sling Media Страницы: 112

Бренд: Ulead Страницы: 168

Бренд: DigiDesign Страницы: 39

FastTrak SX Series Version 4.4

Бренд: Promise Technology Страницы: 102

NORTON INTERNET SECURITY - FOR MAC V4

Бренд: Symantec Страницы: 28

CONFLICTMANAGER

Бренд: Symantec Страницы: 54

PC ANYWHERE SOLUTION V 12.5

Бренд: Symantec Страницы: 63

Бренд: THOMSON Страницы: 22

Navigation app for iPhone/iPad

Бренд: TomTom Страницы: 84

POLICY MANAGER 8.0

Бренд: F-SECURE Страницы: 221

Бренд: Genius Страницы: 3

Бренд: Genius Страницы: 2

VIDEOCAM SLIM USB2

Бренд: Genius Страницы: 4

Бренд: Genius Страницы: 11

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды