Enterasys IRM2 Скачать руководство пользователя

Страница: 44 / 88

Statistics

3-2

Statistics

•

Transmit Collisions

•

Receive Collisions

•

Out-of-Window (OOW) Collisions

•

Giant Packets

•

Alignment Errors

•

CRC Errors

•

Runts

The pie chart to the right of the statistics lets you graphically view your statistics.
The colors in the pie chart correspond to the colors for Packets (green), Collisions
(red), and the two error modes: Hard Errors (blue) and Soft Errors (yellow).

Accessing the Statistics Windows

To access the Repeater Statistics window:

Click on Repeater on the Chassis View menu bar to display the repeater
menu.

Drag down to Statistics... and release. The Repeater Statistics window,

Figure 3-1

, will appear.

Figure 3-1. Statistics Window

NOTE

The Active Users and Broadcasts selections are not available for early generation IRM2s
equipped with pre-version 2.00 release firmware.

Содержание IRM2

























































































Результаты поиска

Содержание IRM2

Отзывы:

Похожие инструкции для IRM2

Бренды по названию

Популярные бренды

Enterasys IRM2, Руководство пользователя

Результаты поиска

Содержание IRM2

Отзывы:

Похожие инструкции для IRM2

Бренды по названию

Популярные бренды