Ensy AHU-300 HH страница 8 Скачать руководство пользователя

Страница: 8 / 36

393870-2 Rev 0: 11.07.2018 BBV

We reserve the right to change technical data without notice.

http://www.ensy.no

Page 7

Main menu

1. Control Button indicator for fan.

2. Control Button indicator set point.

3. Control Button indicator information.

4. Control Button indicator settings.

Overview of control panel

The main screen consists of, from top, left:

Time Indication, hour, minute

Timer, Weekly schedule (if programmed)

Reheating coil (if connected)

Temperature readings, Outdoor / Indoor

Status airflow – fan speed setting

OFF MIN NORM or MAX

Temperature set point, 15 - 21 °C

Reheating coil – (here refers active element)

Rotary exchanger Indicator - (here refers

active rotary wheel)

Indicators in the menu screen:

"Sun" indicates that the rotor has

stopped, the air handling unit is in the

summer operation mode.

"Snowflake" low temperature

indicates that the air handling unit is

in defrosting mode.

"Steaming pot" and blinking fan blades

indicates that the kitchen exhaust is

activated.

"Timer" and the countdown of the fan

symbol indicate that the forced

ventilation is enabled.

From 10 up to 240 minutes

"Away" indicates when the feature is

enabled, this feature will override

timer.

"Clock over the fan symbol" indicates

that the timer is activated.

Co2 over the fan symbol" indicates

that the carbon sensor is activated.

"Exclamation point" indicates that

moisture recorded over the sensor is

higher than the set value.

May also indicate that the motion

sensor is activated if connected on D2

signal output.

Control Button 1.

Содержание AHU-300 HH





































Результаты поиска

Содержание AHU-300 HH

Отзывы:

Похожие инструкции для AHU-300 HH

Бренды по названию

Популярные бренды

Ensy AHU-300 HH, Руководство пользователя и инструкция по установке

Результаты поиска

Содержание AHU-300 HH

Отзывы:

Похожие инструкции для AHU-300 HH

Бренды по названию

Популярные бренды