Ensy AHU-300 HH Скачать руководство пользователя

Страница: 5 / 36

393870-2 Rev 0: 11.07.2018 BBV

We reserve the right to change technical data without notice.

http://www.ensy.no

Page 4

Adjustment of the unit.

A humidity sensor is, from factory, mounted inside the unit. It is set to “0” that

means it is set to not active.

Note!

This switch is not used on units produced before february 2015.

After startup, where the unit is placed into a new building with high

humidity, you can let this humidity sensor be turned off for a period

to avoid the full speed of the fan at night. To get the humidity

sensor to operate as intended, you need at one time to put it active.

Than you need to set the switch in position "1".

If the ventilation unit is placed in a house without high humidity,

you should switch to position "1" after you putting ventilation unit

into operation.

This switch will also affect any extra external humidity sensor that is

plugged into the device.

Adjusting the humidity sensor.

If it is necessary to adjust the sensitivity

of the humidity sensor then you just can

remove the black plug and you then can

see the adjusting knob and the RH%

scale.

Note!

This black plug is not on

units produced before february

2015.

If bad light condition, it may be easier to
remove the cover so that you easier
seethe RH% scale.

The sensor is set to 80% RH from factory.

If you do adjustments, this only affect
the sensor integated inside the unit.

The sensitivity for the integrated sensor
you can adjusted from 50% (low) to 90%
(high) in accordance to what are the
needs. The arrow points the value
chosen.

If you have a second external sensor that
means you need to adjust that one from
its settings.

Replace the cover and / or plug after
finish adjusting.

Содержание AHU-300 HH





































Результаты поиска

Содержание AHU-300 HH

Отзывы:

Похожие инструкции для AHU-300 HH

Бренды по названию

Популярные бренды

Ensy AHU-300 HH, Руководство пользователя и инструкция по установке

Результаты поиска

Содержание AHU-300 HH

Отзывы:

Похожие инструкции для AHU-300 HH

Бренды по названию

Популярные бренды