enphase Enphase Envoy-S Metered Скачать руководство пользователя

Страница: 46 / 49

Envoy-S Installation and Operation



2016 Enphase Energy Inc.

141-00031 Rev 01

Message Shown on
Events and Inventory
Screens

Description

ModuleAdd

Description:

The Envoy has detected and is now associated to a new

microinverter.

No action is required.

Microinverter failed to
report

Recommended Action:

Ignore occasional instances of this event. Communication

usually recovers on the next reporting cycle.

If communications do not recover immediately, ensure that the Envoy is plugged in
very near the Switchboard. Also, if other devices are sharing the AC socket with
the Envoy, remove those devices from the AC socket to improve signal strength.

If the Enphase Envoy was recently relocated or if new devices or appliances were
added to the circuit, it is possible that the new situation is not suitable for power
line communication. The Envoy may need to be relocated to improve signal
strength and reduce interfering noise on the power lines.

To determine the quality of the Envoy’s location for communication, run a
Communications check.

Description:

The Envoy reporting this condition is unable to communicate with the

microinverters over the power lines.

If the condition persists

: See “Power Line Communication Troubleshooting” on

page 34, or contact your installer, or refer to the Troubleshooting Guide at

enphase.com/support

Microinverter grid
configuration failed after 5
attempts, retrying

Description:

The attempt to change the grid profile for the microinverters has

failed after five tries. The Envoy will continue to attempt to change the grid profile.

Recommended Action:

No action is required.

Microinverter grid
configuration failure cleared
after xx attempts

Description:

A failed attempt to change the grid profile for the microinverters has

cleared. The grid profile was successfully applied.

xx = number of attempts

Recommended Action:

No action is required.

ModSleep

Description:

The microinverter is off for the night.

Recommended Action:

No action is required.

No Grid Profile

Recommended Action:

Ask the installer set up select a grid profile for this

system.

Description:

The Envoy has not been set up with a grid profile for the

microinverters.

OverTemperature

Description:

The microinverter is too hot and is not producing power. This very

rare condition usually clears without intervention.

Recommended Action:

No action is required unless the condition persists. If it

persists, contact Enphase Energy customer support.

PwrGenOffByCmd (Power
generation off by
command)

Description:

The microinverter is not producing power by user command. This

uncommon condition will occur only during isolated troubleshooting procedures by
Enphase personnel.

Recommended Action:

No action is required.

PowerOnReset

Description:

The microinverter has powered on after having DC disconnected.

Recommended Action:

No action is required.

RGM Error

Description:

The Enphase-compatible Revenue Grade Meter (RGM) has failed.

Recommended Action:

Contact your installer to arrange for installation of a

replacement meter.

RGM Power Quality
Warning

Description

: The Enphase-compatible Revenue Grade Meter (RGM) reports that

the AC voltage coming from the

grid

is either too low or too high as specified by

applicable regional standards. This is usually a temporary condition that will clear
when power quality from the

local grid

returns to normal.

Recommended Action

: No action is required unless the condition persists. If the

condition persists, contact your installer.

Содержание Enphase Envoy-S Metered


















































Результаты поиска

Содержание Enphase Envoy-S Metered

Отзывы:

Похожие инструкции для Enphase Envoy-S Metered

Бренды по названию

Популярные бренды

enphase Enphase Envoy-S Metered, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Enphase Envoy-S Metered

Отзывы:

Похожие инструкции для Enphase Envoy-S Metered

Бренды по названию

Популярные бренды