Enotec COMTEC 6000 Скачать руководство пользователя страница 65 | Manualshive

Страница: 65 / 67

Enotec COMTEC 6000 Скачать руководство пользователя страница 65

Installation and Operation Manual - COMTEC

®

6000

Warranty

Doc.-ID: COM6000_11022020_EN

65

D

Warranty

E N O T E C W A R R A N T Y

ENOTEC warrants that systems manufactured and sold by it will, upon shipment, be free of defects in workmanship
or material. Should any failure to conform to this warranty become apparent during the relevant warranty periods,
ENOTEC shall, upon prompt written notice from the purchaser, correct such nonconformity by repair or replacement
of the defective part or parts. The purchaser is not entitled to claim any other legal remedies on the basis of this
warranty. Please refer to the ENOTEC international warranty conditions for details.

The warranty durations are as follows:

24 months after delivery for systems.
12 months after delivery for spare parts.

ENOTEC accepts no responsibility or liability for defects and damage to ENOTEC products which are to be attributed
to the following causes: Wear, corrosion, improper use, unauthorized modifications, inadequate maintenance and
non-compliance with the operating instructions.

All ENOTEC products and systems which incorporate a heated sensor must be operated under continuous
conditions. If the heater power is switched off and on regularly, the resultant thermal stress for the probe heater,
probe thermocouple and sensor will cause a shorter life span. If it is not possible to operate the heated equipment
continuously for a longer period of time, please contact ENOTEC for technical advice.

Note: When installing the equipment, the customer must ensure that all necessary supply lines are connected and
the operating temperature of the probe is reached. Experience has shown that products installed but not put into
operation may be damaged by the process or by external influence. ENOTEC will not accept any responsibility for
such damages.

Suitable tools must be used when installing and commissioning ENOTEC products and systems. If any damage is
caused due to the use of unsuitable tools, ENOTEC will not accept any responsibility for damages.

MANUFACTURER:

ENOTEC

GmbH

Höher

Birken

6

D-51709

Marienheide,

Germany

TEL:

+49 (0) 2264 / 45780

FAX: +49 (0) 2264 / 457830

Email:

[email protected]

«
...
63
64
65
66
67
»

Содержание COMTEC 6000




































































Отзывы:

Нет отзывов