manualshive.com logo in svg

Enotec COMTEC 6000, Руководство по сборке, установке и эксплуатации, Страница: 45 / 67

Поделиться
Скачать
Enotec COMTEC 6000 Скачать руководство пользователя страница 45

Installation and Operation Manual  - COMTEC

®

 6000 

Status Messages

 

Doc.-ID: COM6000_11022020_EN 

45 

Error Messages

 (cont.) 

Error  
Message 

Relay 
contact 

O

2

 signal  

output 

Description 

O2 sensor 
offset too 
high 

System 
error, 
open 

 

The error can only occur during an O2 sensor calibration. An error reset can be 
carried out by the user. A successful re-calibration also resets the error. 

Possible causes:

 defective false test gas (not applicable with test air), test gas 

flow too low, O2 sensor defective. 

O

2

 sensor 

slope too 
low 

System 
error, 
open 

 

The error can only occur only during an O

2

 sensor calibration. An error reset can 

be carried out by the user. A successful re-calibration also resets the error.  

Possible causes:

 Incorrect calibration gas, test gas flow too low, probe filter 

damaged, filter head missing, faulty O

2

 sensor. 

O

2

 sensor 

slope too 
high 

System 
error, 
open 

 

The error can only occur only during an O

2

 sensor calibration. An error reset can 

be carried out by the user. A successful re-calibration also resets the error.  

Possible causes:

 Incorrect calibration gas, O

2

 sensor defective. 

O

2

 sensor 

signal  
instable

 

System 
error, 
open

 

 

The error can only occur only during an O

2

 sensor calibration. An error reset can 

be carried out by the user. A successful re-calibration also resets the error.  

Possible causes:

 test gas flow too low, probe filter is damaged, process 

pressure fluctuations too high.

 

CO

e

 board 

communicatio
n error

 

 

20.80mA 
unless set 
otherwise

 

The error can occur at any time and signals a failure in communication between 
the display circuit board and the CO

e

 circuit board. A reset can be carried out by 

the user. If the error occurs again, switch the system on and off. If the error 
persists after restarting the system, contact an ENOTEC service point.

 

CO

e

 sensor 

heater short 
circuit 

 

20.80mA 
unless set 
otherwise

 

The error can occur at any time and signals a short circuit either by CO

e

 sensor 

heating or within the connection between the electronic unit and CO

e

 sensor. A 

reset can be carried out by the user. 

Possible causes:

 Short-circuit of the CO

e

 sensor heater cable at the terminal 

points of the electronics or the sensor, short circuit within the probe cable, short 
circuit inside the COe sensor 

CO

e

 sensor 

heater short 
circuit 

 

20.80mA 
unless set 
otherwise

 

The error can occur at any time and signals a break in the circuit of CO

e

 sensor 

heater. A reset can be carried out by the user, once the fault has been remedied. 

Possible causes:

 contact problems  between CO

e

  sensor cable and  terminal 

points of the electronics respectively  the probe, probe cable is damaged, defective 
COe sensor 

Open circuit 
CO

e

 sensor 

heating 

 

20.80mA 
unless set 
otherwise

 

The error can occur at any time and signals a break in the circuit of CO

e

 sensor. A 

reset can be carried out by the user, once the fault has been remedied. 

Possible causes:

 contact problems CO

e

 sensor wire to the terminal points of the 

electronics and the probe, probe cable is damaged, defective CO

e

 sensor 

Open circuit 
CO

e

 sensor 

 

20.80mA 
unless set 
otherwise

 

The error can occur at any time and signals a failure of the electronic components 
of the CO

e

 board. A reset cannot be carried out by the user. If the error persists 

after restarting the system, contact an ENOTEC service point. 

COe board 
hardware 
error A-C 

 

20.80mA 
unless set 
otherwise

 

CO

e

 sensor calibration failed for one of the following reasons. A reset cannot be 

carried out by the user. All entries triggered by this error will then also be deleted. 

CO

e

 sensor 

calibration 
failed 

 

20.80mA 
unless set 
otherwise

 

CO

e

 sensor calibration failed for one of the following reasons. A reset cannot be 

carried out by the user. All entries triggered by this error will then also be deleted. 

CO

e

 sensor 

offset too 
low/high 

 

20.80mA 
unless set 
otherwise

 

The error can only occur only during COe sensor calibration. A reset cannot be 
carried out by the user. A successful re-calibration remedies the error. Possible 
causes: insufficient supply of reference air. 

CO

e

 factor 

alpha/beta/ 
gamma 
invalid 

 

20.80mA 
unless set 
otherwise

 

The error can only occur only during CO

e

 sensor calibration. It can be reset by the 

user. A reset cannot be carried out by the user. A successful re-calibration also 
remedies the error. 

Possible causes:

 inadequate reference air supply, process pressure is too high, 

incorrect test gas (not test air), CO

e

 sensor defective. 

Error 
ENOTEC 
REMOTE

 

module 

System 
error, 
open 

 

Indicates a hardware error of the ENOTEC REMOTE

 

module.  

Possible cause:

 the ENOTEC REMOTE

 

module is defective. 

Unlisted errors: Other errors cannot be remedied by the customer. 
Please contact an ENOTEC service point   

Содержание COMTEC 6000




































































Отзывы:

Нет отзывов