Enotec COMTEC 6000 Скачать руководство пользователя страница 48

Страница: 48 / 67

Troubleshooting

Installation and Operation Manual - COMTEC

6000

Doc.-ID: COM6000_11022020_EN

Local Displays correct, Output not correct

Possible reasons

Procedure

Electronic unit is defective

Check measuring range. Check whether the current
value is outside the measuring range

Electronic unit is defective

Measure the mA output on the strip terminal.

reads higher than expected, and CO

reads lower than expected

Possible reasons

Procedure

This may be due to a poor seal of the CO

sensor coupling

located in the terminal box housing. If the stainless steel nut
is not tight enough the O-ring seal allows ambient air to
enter into the CO

senor mounting tube which influences

the sensors readings

Tighten or replace the CO

sensor coupling assembly.

No COe-Measuring Value; Arrow instead of a value

Possible reasons

Procedure

The physical measuring range has been exceeded

Perform a O

+ CO

sensor check

An error has occurred with the CO

sensor

Check all electrical connections.

No Measuring Value for O

; empty Bar Graph

Possible reasons

Procedure

value out of the coverage of the electronic unit, for

example caused by a low O

concentration in connection

with a high COe concentration

Perform an O

+ CO

sensor check

Содержание COMTEC 6000




































































Результаты поиска

Содержание COMTEC 6000

Отзывы:

Enotec COMTEC 6000, Руководство по сборке, установке и эксплуатации, Страница: 48 / 67

Результаты поиска

Содержание COMTEC 6000

Отзывы: