Enotec COMTEC 6000 Скачать руководство пользователя страница 51 | Manualshive

Страница: 51 / 67

Enotec COMTEC 6000 Скачать руководство пользователя страница 51

Installation and Operation Manual - COMTEC

®

6000

Technical Data

Doc.-ID: COM6000_11022020_EN

51

Requirements of the Gas Supply

The analyzer system uses the connected instrument air continuously for the supply of
reference air, and during calibration and system test respectively, for the supply of test air (test gas 1).

Instrument air supply

for reference air

/

test air

Specification:

According to ISO 8573-1 class 2
(Particle size max. 1



m,

Particle density max. 1mg/m³,
Oil content max. 0,1mg/m³,
Pressure dew point max. -40 °C or 10 °C below lowest possible ambient temperature
Constant 20,95 Vol. %O

2

Input pressure:

2-10 bar

Flow rate

continuously maximum 40 l/h (for reference air supply)
180 l/h during calibration

Test gas (test gas bottle)

for calibration / system test

Input pressure:

max. 3 bar

Specification
test gas 1 (optional):

21% O

2

in N

2

(synthetic air – in case instrument air is not available)

Specification
test gas 2:

The test gas used for calibration purposes must have the exact same composition as the
test gas specified in the test certificate. The test certificate can be found attached to the
probe / sensor on delivery.
The test gas recommendations for O

2

and CO

e

sensor may possibly differ. In this case,

the sensors must be individually calibrated.

Flow rate

180 l/h at 1,1 bar (+/- 0,1).

Note

The flow rate of the test gas bottle is set via the bottle pressure regulator.

«
...
49
50
51
52
53
...
»

Содержание COMTEC 6000




































































Отзывы:

Нет отзывов