background image

 
 
 
 
ENIGMA XM88422 Digital Receiver 

 

Version 1.50 

 

 

31 

6. Power Module 

The  Power  Module  supplies  power  to  the  other 
modules  in  the  system,  charges  and  supervises  the 
backup  battery  and  reports  AC  and  battery  status  to 
the CPM Unit. 

Inputs and Outputs 

The  input  of  the  Power  Module  is  16.5  VAC.  The 
module  contains  a  dual  power  supply,  separate 
power  supplies  for  the  modules  and  for  battery 
charging. The red AC Power light on the front of the 
Power  Module  indicates  the  presence  of  the  AC 
voltage. 
 
For  the  other  modules  in  the  system  the  Power 
Module  makes  13.2  V  DC  stabilized  power  with  a 
maximum  static  load  of  3  Amps.  This  voltage  is 
spread for the modules on the power bus. The other 
voltages  (stabilized  5V  DC,  110  VAC  for  the 
backlights)  are  created  inside  the  modules  to 
minimize  static  and  electric  noise  sensitivity  and  EM 
radiation. 
 
For battery charging the Power Module makes 13.8 V 
DC stabilized power. The maximum battery charging 
current is 1.5 Amps.  

Battery Status 

The  Battery  light  on  the  front  of  the  Power  Module 
indicates the status of the battery. The battery status 
can be the following 
 

Steady green light 

Indicates  that  the  battery  is  present  and  the  battery 
capacity  is  in  order.  The  Power  Module  reports 
“Battery OK” 
 

Flashing green light 

Indicates  that  the  battery  is  present,  however  the 
battery capacity is below the required minimum. The 
Power Module reports “Battery Low”. This can occur, 
if  a  discharged  battery  is  connected,  or  the  nominal 
capacity of the battery is below 6 Ah. If the battery is 
discharged,  leave  the  battery  connected  and  the 
Power  Module  will  charge  it  up.  After  reaching  the 
required  capacity,  the  light  will  go  steady  green  and 
the  Power  Module  will  report  “Battery  OK”.  If  the 
battery will not reach the required capacity even after 
a  long  time  (1  day)  replace  the  battery  to  ensure 
reliable  battery  backup  operation  in  case  of  AC 
failure. 
 

Flashing red light 

If the Battery LED flashes red, that means that either 
no  battery  is  connected,  or  the  battery  connection  is 
broken  or  the  battery  is  deeply  discharged.  In  this 
case,  always  check  battery  connections  and  replace 
the  battery,  because  the  receivers  battery  backup 
operation will not be reliable under such conditions. 

Battery Testing 

The Power Module checks for battery presence every 
minute,  and  conducts  an  active  battery  test  in  every 
hour. It also makes the active test after the battery is 
connected to the receiver.  
 
When  checking  for  battery  presence,  the  Power 
Module  checks  the  voltage  on  the  battery  terminals 
with  decreasing  the  charging  voltage  applied.  If  the 
voltage is below a preprogrammed limit, it will cause 
a battery fail event. 
 
The  active  test  is  conducted  only  when  a  battery  is 
connected  to  the  receiver.  During  the  active  test  the 
Power  Module  first  disconnects  charging  voltage 
entirely. If the voltage of the battery does not drop, it 
applies  a  load  to  the  battery  and  observes  the 
gradient  of  the  voltage  drop.  If  the  voltage  of  the 
battery sinks too fast, or falls below a limit, the Power 
Module will cause a battery fault event. 
 

IMPORTANT:

 The battery will be considered OK only 

if  it  passes  the  active  test.  Therefore  small  capacity 
batteries  will  never  be  found  good.  The  minimum 
recommended  battery  capacity  for  the  ENIGMA 
receiver is 7 Ah. 

Содержание XM88422





































Отзывы: