background image

SET‐UP & OPERATIONS

4.

Install a “

Battery Pack

” into the “

Remote Transceiver Pack

” as follows:

a.

Open the battery compartment by sliding the tab cover located on the front of 
the “

Remote Transceiver Pack

” outwards.

b.

Insert a “

Battery Pack

” into the battery compartment checking that battery 

and compartment’s contacts (+/‐) are properly aligned.  

c.

Once inserted press the “

Battery Pack

” downwards to secure it into position 

and then close the battery compartment by sliding its tab cover inwards.  

NOTE:

When properly inserted, the LED located on the “

Remote Transceiver 

Pack

” will flash on/off and then remain solid indicate that the device is 

receiving power and is linked to the “

Transceiver Base Station

.”

5.

Repeat steps 

4a – 4c

to install “

Battery Packs

” into the remaining “

Remote 

Transceiver Packs

.” 

6.

Connect a “

Headset

” to each “

Remote Transceiver Pack

,” by inserting the plugs 

located on the cable lead wired to the “

Headset

” into the corresponding jacks 

located on the outer/left of the “

Remote Transceiver Pack

.”

7.

To allow 

ALL

corresponding “

Remote Transceiver Packs

” to simultaneously talk and 

listen to one another, set the “

Transceiver Base Station

” to “

Conference

” operating 

mode by pressing the device’s 

green

CONFERENCE

” button. 

NOTE:

The 

red

LED 

located on the front of the “

Transceiver Base Station

” will turn on and remain solid 

when the device is set to “

Conference

” operating mode.

**

The WRAPS

System’s Transceiver Base Station 

MUST 

be powered on

BEFORE

any of the 

corresponding Remote Transceiver Packs are powered on to allow a link to be 
established!

For optimum range/performance the Transceiver Base Station should be positioned on 
an elevated surface that is centrally located between the operators equipped with 
Remote Transceiver Packs with no/minimal signal path obstructions.

Pg. 6 of 11

**

The WRAPS

System’s Transceiver Base Station features (2) operating mode settings:

Dual‐Channel

Conference

The operating mode setting of the “

Transceiver Base Station

” determines which “

Remote 

Transceiver Packs

” can simultaneously talk and listen to one another.  

For complete details, please review the “

TRANSCEIVER BASE STATION PROGRAMMING 

CHANNEL GROUPS & OPERATING MODE SETTINGS

” section of this manual.

Ops Ver. 03/18

Remote Transceiver Pack

Headset Jacks

Transceiver Base Station

“CONFERENCE” Button

(Conference Mode Active)

Remote Transceiver Pack 

Battery Compartment 

Headset

Содержание ETG-WRAPS-SYS













Отзывы: