background image

REMOTE TRANSCEIVER PACK & TRANSCEIVER BASE STATION 

PROGRAMMING

Clearing All Transceiver Base Station Programming Channel Settings:

If at any time a new or additional Remote Transceiver Pack is to be used, one must clear 

ALL

existing Transceiver 

Base Station Programming Channel Group settings and then program 

EACH

Remote Transceiver Pack to the 

device.

Transceiver Base Station’s

Programming Pad

(Clip Removed)

1.

Check that 

ALL

Remote Transceiver Packs

” are powered 

OFF

.

2.

Access the “

Programming Pad

” located behind the clip located on the rear of the 

Transceiver Base Station

” as follows:

a.

Gently pull the gray tab arm located in the middle behind the clip away 
from the “

Transceiver Base Station

” to release tension.

b.

While the gray tab arm is being pulled, slide the clip off the “

Transceiver 

Base Station

” by pushing it upwards to reveal/provide access to the 

Programming Pad

.” 

3.

Install a “

Battery Pack

” into the “

Transceiver Base Station

” and power it on by 

rotating the device’s “

ON‐OFF/VOL.

” dial to the left.  

NOTE:

After the device has 

been powered on both “

Programming Pad

” LEDs will flash on/off and then turn 

off.

4.

To clear “

Programming Channel Group #1

,” follow these steps:

a.

Press and hold down the “

#1 Programming Button

” for approx. (5) 

seconds until its corresponding LED begins to flash on and off then release.

b.

While the corresponding LED is flashing on and off, press the “

#1 

Programming Button

” (7) consecutive times. 

NOTE:

When this is 

performed, the corresponding LED will begin to rapidly flash on/off for 
approx. (10) seconds and will then turn off indicating that all the 

Programming Channel Group #1

” settings have been cleared. 

5.

To clear “

Programming Channel Group #2

,” follow these steps:

a.

Press and hold down the “

#2 Programming Button

” for approx. (5) 

seconds until its corresponding LED begins to flash on and off then release.

b.

While the corresponding LED is flashing on and off, press the “

#2 

Programming Button

” (7) consecutive times. 

NOTE:

When this is 

performed, the corresponding LED will begin to rapidly flash on/off for 
approx. (10) seconds and will then turn off indicating that all the 

Programming Channel Group #2

” settings have been cleared. 

6.

Power off the “

Transceiver Base Station

” rotating its “

ON/OFF VOL.

” to the right 

until a “click” sound is produced

.  

NOTE:

When powered off the device’s “

POWER 

STATUS

” LED will turn off.

After steps 1‐6 have been performed all the Transceiver Base Station Program Channel Group settings have been 
cleared and the device is now ready to be programmed to the Remote Transceiver Packs.

Transceiver Base Station 

Clip’s Gray Pull Arm

Pg. 10 of 11

Ops Ver. 03/18

Содержание ETG-WRAPS-SYS













Отзывы: