background image

  

- VI - 

DISCLAIMER 

The  information  and  instructions  contained  within  this  publication  comply  with  all  FCC,  GCF,  PTCRB, 
R&TTE, IMEI and other applicable codes that are in effect at the time of publication. Enfora disclaims all 
responsibility  for  any  act  or  omissions,  or  for  breach  of  law,  code  or  regulation,  including  local  or  state 
codes,  performed  by  a  third  party.  Enfora  strongly  recommends  that  all  installations,  hookups, 
transmissions,  etc.,  be  performed  by  persons  who  are  experienced  in  the  fields  of  radio  frequency 
technologies.  Enfora  acknowledges  that  the  installation,  setup  and  transmission  guidelines  contained 
within  this  publication  are  guidelines,  and  that  each  installation  may  have  variables  outside  of  the 
guidelines contained herein. Said variables must be taken into consideration when installing or using the 
product,  and  Enfora  shall  not  be  responsible  for  installations  or  transmissions  that  fall  outside  of  the 
parameters set forth in this publication. 

BATTERY INFORMATION AND SAFETY REQUIREMENTS 

NOTE: Failure to comply with all of the following precautions could: 

 

Cause personal injury or property damage 

 

Cause abnormal chemical reactions which would make the battery over heat, smoke, distort, leak, or 
catch on fire 

 

Destroy internal protections built into the battery 

 

Shorten battery life 

 

Reduce battery performance 

  

Precautions 

 

Read this entire manual and the label on the exterior of the battery. 

 

Keep the battery away from sources of excessive heat such as fire, stoves, or direct sunlight. 

 

Keep the battery away from sources of high voltage or static discharge. 

 

Do not use or store the battery with other batteries or where it could touch metal. 

 

Do not put the battery into a microwave oven. 

 

Do not allow the battery to be crushed. 

 

Keep the battery away from children. 

 

Do not drop the battery. 

 

Do not allow anything to touch any of the battery contacts, or to connect two or more of the 
contacts. 

 

Do not disassemble, destroy, or attempt reassembly of the battery. 

 

Do not place or leave the battery in a damp or wet environment. 

 

Do not allow water to touch the battery. 

 

Do not wrap the battery with conductive material. 

Содержание Enfora Mini MT























































Отзывы: