Enerzone Destination 1.6 страница 55 Скачать руководство пользователя

Страница: 55 / 60

Destination 1.6 Installation and Operation Manual

Appendix 4: Installation of Secondary Air Tubes and Baffle

1- Starting with the rear

tube, lean and insert the

right

end

the

secondary air tube into

the rear right channel

hole (DETAIL 1). Then

lift and insert the left end

of the tube into the rear

left channel.

2- Align the notch in the

left end of the tube with

the key of the left air

channel hole. Using a

« Wise grip » hold the

tube and lock it in place

by turning the tube as

shown in (DETAIL 2).

Make sure the notch

reaches the end of the

key way.

3- Repeat step 1 and 2 for

the other secondary air

tubes.

4- To remove the tubes

use the above steps in

reverse order.

Содержание Destination 1.6





























































Результаты поиска

Содержание Destination 1.6

Отзывы:

Похожие инструкции для Destination 1.6

Бренды по названию

Популярные бренды

Enerzone Destination 1.6, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Destination 1.6

Отзывы:

Похожие инструкции для Destination 1.6

Бренды по названию

Популярные бренды