Enerzone Destination 1.6 страница 30 Скачать руководство пользователя | Manualshive

Страница: 30 / 60

background image

30

Destination 1.6 Installation and Operation Manual

thick layer of creosote to form. When you avoid smouldering so the exhaust from the chimney is
mostly clear, creosote builds up more slowly. Your new stove has the right characteristics to help
you to burn clean fires with little or no smoke, resulting in less creosote in the chimney.

5.2.2 How Often Should You Clean the Chimney?

It  is  not  possible  to  predict  how  much  or  how  quickly  creosote  will  form  in  your  chimney.  It  is
important, therefore, to check the build-up in your chimney monthly when getting used to the new
stove  until  you  determine  the  rate  of  creosote  formation.  Even  if  creosote  forms  slowly  in  your
system, the chimney should be cleaned and inspected at least once each year.

It is recommended to clean thoroughly the chimney system at the end of every heating season.
During summer, the air is damper and with minimal air circulation within the stove or furnace, it can
mix with creosote and/or sooth deposits in the chimney system to form an acid that could
accelerate the corrosion process and induce premature decay of the steel. Corrosion damages are
not covered under warranty. Have your chimney system cleaned by a professional chimney sweep.
Use a plastic or steel brush.

Contact your local municipal or provincial fire authority for information on how to handle a chimney
fire. Have a clearly understood plan to handle a chimney fire.

5.2.3 Cleaning the Chimney

Chimney cleaning can be a difficult and
dangerous

job.

If

you

don’t

have

experience  cleaning  chimneys,  you  might
want to hire a professional chimney sweep
to clean and inspect the system for the first
time.  After  having  seen  the  cleaning
process,  you  can  decide  if  it  is  a  job  you
would like to take on.

The most common equipment used are
fibreglass rods with threaded fittings and
stiff plastic brushes. The brush is forced up
and down inside the chimney flue to scrub
off the creosote.

The chimney connector assembly should
always be cleaned at the same time the
chimney is cleaned.

CAUTION:    Operation  of  your  stove  without  the  baffle  may  cause  unsafe  and  hazardous
temperature conditions and will void the warranty.  NOTE:  Before installing the firebrick, check to
ensure  that  none  are  broken  or  damaged  in  any  way.    If  so,  have  the  damaged  ones  replaced.
Check  the  firebrick  for  damage  at  least  annually  and  replace  any  broken  or  damaged  ones  with
new ones.  Inspection and cleaning of the chimney is facilitated by the removable baffle.

«
...
28
29
30
31
32
...
»

Содержание Destination 1.6





























































Отзывы:

Нет отзывов

Похожие инструкции для Destination 1.6

Бренд: Kalor Страницы: 48

Бренд: Italiana Camini Страницы: 159

Бренд: United States Stove Страницы: 60

Бренд: Quadra-Fire Страницы: 40

Бренд: Charlton & Jenrick Страницы: 40

Freestanding Severn Stove with Boiler

Бренд: Coalbrookdale Страницы: 7

Much Wenlock Stove

Бренд: Coalbrookdale Страницы: 8

Бренд: Upland Страницы: 12

Бренд: Pincheng Страницы: 26

Бренд: PASIAN Страницы: 57

Defiant FlexBurn 1975

Бренд: Vermont Castings Страницы: 22

Бренд: Elma Страницы: 20

Бренд: Montigo Страницы: 20

AGENCY PHASE II

Бренд: STEERS Страницы: 37

Бренд: Palazzetti Страницы: 96

Бренд: Drolet Страницы: 56

Бренд: Tecno Air System Страницы: 40

Бренд: ZANTIA Страницы: 88

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды