Enerzone Destination 1.6 Скачать руководство пользователя страница 36 | Manualshive

Страница: 36 / 60

background image

36

Destination 1.6 Installation and Operation Manual

7.3 Floor protector

Your stove is designed to keep the floor from overheating. It should be placed on a non
combustible surface to protect the floor of hot embers that could fall from the stove during loading
and maintenance. As shown in the table below and the figure Clearances to combustibles and
floor protection, there are differences between the floor protections in Canada and in the United
States.

FLOOR PROTECTOR*

CANADA

USA

G

8’’ (203 mm) – Note 1

N/A (Canada only)

H

8’’ (203 mm)

N/A (Canada only)

I

18’’ (457 mm)

From door opening

16’’ (406 mm)

From door opening

J

N/A (USA only)

8’’ (203 mm)

M

8’’ (203 mm)

N/A (Canada only)

N

N/A (USA only)

Note 2

*Steel with a minimum thickness of 0.015’’ (0.38 mm) or ceramic tiles sealed together with
grout. No protection is required if the unit is installed on a non-combustible floor (ex: concrete).

Note 1: The floor protection at the back of the stove is limited to the stove’s required clearance

if such clearance is smaller than 8 inches (203 mm).

Note 2: Only required under the horizontal section of the connector. Must exceed each side of

the connector by at least 2 inches (51 mm).

«
...
34
35
36
37
38
...
»

Содержание Destination 1.6





























































Отзывы:

Нет отзывов

Похожие инструкции для Destination 1.6

Бренд: HAAS + SOHN Страницы: 24

Бренд: Migali Страницы: 24

Бренд: Jøtul Страницы: 20

Бренд: HASE Страницы: 116

Бренд: DeLonghi Страницы: 7

Stove with 3,6 kW PnP

Бренд: Karibu Страницы: 68

Бренд: Royal Страницы: 20

ECOMONOBLOCCO WT F Series

Бренд: Palazzetti Страницы: 104

Бренд: Drolet Страницы: 45

Бренд: ECG Страницы: 76

Бренд: Kenyon Страницы: 2

Бренд: Kenyon Страницы: 12

Бренд: Drolet Страницы: 64

Ecofire GISELLE

Бренд: Palazzetti Страницы: 12

Бренд: Survivor Страницы: 14

Бренд: Saey Страницы: 40

Бренд: Varde Страницы: 20

Turia Lina Compact Series

Бренд: Olsberg Страницы: 44

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды