ENERGY KINETICS EK1C, Инструкция по установке и обслуживанию

Страница: 31 / 75

Accel CS Boiler - Gas Heat - Eighth Edition – January, 2015 30
GENERAL ASSEMBLY
Assembly of various packaged units is illustrated throughout this manual. The use of non-Energy Kinetics supplied
pumps, controls and accessories should follow good practices. The diagrams and locations presented in this manual are
recommended.
WARNING: Boiler shall be installed such that the gas ignition system components are protected from water (dripping,
spraying, rain, etc.) during appliance installation, operation, and service (circulator, control, etc.,
replacement).
BOILER MOUNTING
The Accel CS boiler can be mounted either free standing on a base or EK1C’s may be mounted on a wall (wall mounting
for EK2C and EK3C is not recommended). Mounting the boiler on a base and standing the boiler near a wall will make for
a clean looking installation, because wiring and piping running behind the boiler will be hidden from view.
BOILER MOUNTING ON BOILER BASE
The boiler ships from the factory mounted to the stand. Bolts go up through the holes in the base and are threaded into
the weld-nuts in the bottom of the boiler.
BEST PRACTICE: Use the cardboard from the shipping container to protect the enclosure and the floor from scratches
while handling the boiler.
WARNING: The boiler is heavy and it is recommended that two or more people carry or lift the boiler. It is recommended
that leather gloves are worn while handling the boiler to prevent the possibility of cuts from the edges of the
sheet metal chassis.
The boiler should only be lifted from the bottom and back of the enclosure. Front covers may be left on. Do not try to lift
by the piping or any other system components.
If for some reason the mounting base needs to be replaced, with help from a second person, lay the boiler down on back
of the unit. Using hardware provided, thread a bolt with a flat washer through one of the four mounting holes in the top of
the base and thread it into the corresponding threaded hole in the bottom of the chassis. Install all four by hand, and then
tighten with wrench. With help from a second person, stand the boiler with base attached up and move into place for
installation.
WALL MOUNTING THE EK1C BOILER
Wall mounting requirements
The wall must be plumb and capable of carrying the
weight of the boiler, water, and any piping components
attached, plus a reasonable safety margin.
A water filled Accel CS EK1C boiler weighs over 250
pounds, an EK2C weighs over 375 pounds, and an EK3C
weighs well over 500 pounds. Add the weight of any
additional components, such as piping, zone circulators,
etc. Failure to comply could result in severe personal
injury, death, or substantial property damage.
WARNING: Do not attempt to attach the wall mounting
brackets using any means other then direct
attachment to wall studs or equivalent
structure if studs are not available.
WARNING: Verify that the studs and structure are
suitable for carrying this wall mounted load.
There are four holes in the bracket, two on each side.
The mounting holes are designed for ¼” diameter
fasteners. Attach the top mounting bracket so the smaller
flange is on top, using four fasteners as it carries the
weight of the boiler. Attach the bottom bracket so the
larger flange is on top and may be installed using two fasteners, one per side as it only spaces the boiler out from the
wall/mounting panel.
CLEARANCE FOR
1/4" FASTENERS
(40
5
8
")
3"
36
5
8
"
23
1
4
"
1
3
16
"
12" MINIMUM
FLOOR
WALL/MOUNTING PANEL
3
8
" FLANGE UP
5
8
" FLANGE UP
*NOTE:
UPPER AND LOWER BRACKET
ARE THE SAME PART MOUNTED
AS MIRROR IMAGES. THE
SMALLER
3
8
" FLANGES ARE
MOUNTED TO THE OUTSIDES AND
LARGER
5
8
" FLANGES MOUNTED TO
THE CENTER.
CEILING
20" MINIMUM
UPPER*
LOWER*