Endress+Hauser RMS621 Скачать руководство пользователя страница 40 | Manualshive

Страница: 40 / 77

background image

Commissioning

RMS621

40

Hauser

Temperature inputs

Function (menu item)

Parameter setting

Description

Identifier

Temperature 1-6

Name of temperature sensor, e.g. ’Temp 1’ (max. 12
characters).

Signal

Select

4-20 mA
0-20 mA
Pt100
Pt500
Pt1000
Default

Selects the signal of the temperature sensor. If ’Default’ is set,
the device works with a fixed default temperature.

Sensor type

3-wire

4-wire

Configures the sensor connection in 3-wire or 4-wire
technology.

!

Note!

Can only be selected for the Pt100/Pt500/Pt1000 signal.

Terminals

None

A-10; A-110; B-112;
B-113; C-112; C-113; D-
112; D-113; B-117; B-
121; C-117; C-121; D-
117; D-121; E-1-6;
E-3-8

Defines the terminal for connecting the temperature sensor. It
is possible to use a sensor signal for several applications. For
this, in the application in question, select the terminals where
the sensor is located (multiple selection possible).

!

Note!

The term in brackets X-1X (e.g. A-11) describes a current
input, the term X-2X (e.g. E-21) a pure temperature input. The
type of input depends on the extension cards.

Unit

°C

; K; °F

Physical unit of the measured temperature.

!

Note!

Only visible if the "Random" system unit has been selected.

Format

9;

9.9

; 9.99; 9.999

Number of places after the decimal point

!

Note!

Only visible if the "Random" system unit has been selected.

Signal damp

0 to 99 s

0 s

Time constant of the first order low pass for the input signal.
This function is used to reduce display fluctuations in the event
of severely fluctuating signals.

!

Note!

This can only be selected for the 0/4 to 20 mA signal.

Start value

-9999.99 to 999999

Start value for the temperature with 0 or 4 mA.

!

Note!

This can only be selected for the 0/4 to 20 mA signal.

End value

-9999.99 to 999999

End value for the temperature with 20 mA.

!

Note!

This can only be selected for the 0/4 to 20 mA signal.

Offset

-9999.99 to 9999.99

0.0

Shifts the zero point of the response curve. This function is
used to adjust sensors.

!

Note!

This can only be selected for the 0/4 to 20 mA signal.

Default

-9999.99 to 9999.99

20 °C or 70 °F

Sets the temperature which is worked with if the sensor signal
fails and the ’Default’ signal is set.

Alarm response

See Setup ’Flow inputs’.

Temperature mean value

Unused

2 sensors
3 to 6 sensors

Mean value computed from several temperature signals
(See Section 11.2.1 for details of the 'Mean value
computation')

«
...
38
39
40
41
42
...
»

Содержание RMS621














































































Отзывы:

Нет отзывов

Похожие инструкции для RMS621

Бренд: Samson Страницы: 32

Бренд: Quantum Страницы: 15

Бренд: Walimex Pro Страницы: 68

Бренд: Zamel Страницы: 2

Бренд: Zamel Страницы: 2

Бренд: Zamel Страницы: 2

Бренд: Unitech Страницы: 55

Бренд: S&C Страницы: 8

Бренд: Gardena Страницы: 236

Бренд: M-system Страницы: 10

JetWeb JX2-PRN1

Бренд: Jetter Страницы: 25

TBEN-L 8IOL Series

Бренд: turck Страницы: 148

APEXpy 07-37A2-2111/ 520Series

Бренд: Bartec Страницы: 98

Бренд: Burlington Страницы: 7

Бренд: Securi-Prod Страницы: 3

Бренд: Yolink Страницы: 23

Бренд: Frico Страницы: 8

Ratio Feeder J+ Advanced Series

Бренд: H.E. Anderson Страницы: 11

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды