Endress+Hauser RMS621 Скачать руководство пользователя страница 49 | Manualshive

Страница: 49 / 77

background image

RMS621

Commissioning

Hauser

49

Relay/set point

Relays or passive digital outputs (open collector) are available in the relay for limit functions.
Depending on the version, 1 to 13 limit values (set points) are available.

Simulation

0.0 Hz - 0.1 Hz - 1.0 Hz -
5.0 Hz - 10 Hz - 50 Hz -
100 Hz - 200 Hz - 500 Hz
- 1000 Hz - 2000 Hz

Off

The function of the pulse output is simulated with this setting.
Simulation is active if the setting is not "off". Simulation ends if
you leave this item.

Function (menu item)

Parameter setting

Description

Identifier

Set point 1 to 13

An identifier can be assigned to the set point in question for a
better overview (max. 12 characters).

Transmit by

Display
Relay
Digital

Select

Assigns where the set point is output (passive digital output
only available with extension card).

Terminals

A-52, B-142, B-152,
C-142, C-152, D-142, D-
152
B-135, B-137, C-135, C-
137, D-135, D-137

None

Defines the terminal of the set point selected.
Relay: terminals X-14X, X-15X

Digital: terminals X-13X

Op. mode

Max+Alarm,
Grad.+Alarm, Alarm, Min,
Max, Gradient, Wet steam
alarm, Unit failure

Min+Alarm

Definition of the event which should activate the set point.

•

Min+Alarm

Minimum safety, event report when set point is undershot
with simultaneous signal source monitoring to NAMUR
NE43.

•

Max+Alarm

Maximum safety, event report when set point is overshot
with simultaneous signal source monitoring to NAMUR
NE43.

•

Grad.+Alarm

Gradient analysis, event report when set signal change is
overshot per time unit of the signal source with
simultaneous signal source monitoring to NAMUR NE43.

•

Alarm

Signal source monitoring to NAMUR NE43, no set point
function.

•

Min

Event report when set point is undershot without taking
NAMUR NE43 into consideration.

•

Max

Event report when set point is overshot without taking
NAMUR NE43 into consideration.

•

Gradient

Gradient analysis, event report when set signal change is
overshot per time unit of the signal source without taking
NAMUR NE43 into account.

•

Wet steam alarm

Relay (output) switches in the event of a wet steam alarm (2
C above saturated steam temperature).

•

Unit failure

Relay (output) switches if a device fault is present (fault
message).

Sig. source

Flow 1, Heat flow 1, Mass
sum 1, Flow 2, etc.

Select

Signal sources for the selected set point.

!

Note!

The number of signal sources depends on the number of
configured applications and inputs.

Swit. point

-99999 to 99999

0.0

Smallest output value of the analog output.

Function (menu item)

Parameter setting

Description

«
...
47
48
49
50
51
...
»

Содержание RMS621














































































Отзывы:

Нет отзывов

Похожие инструкции для RMS621

Бренд: MADRIX Страницы: 36

Бренд: EA Страницы: 24

Minas A4 Series

Бренд: Panasonic Страницы: 5

Бренд: Acclaim Lighting Страницы: 32

Бренд: Jeep Страницы: 19

Бренд: B&R Industries Страницы: 89

Бренд: Saga Страницы: 9

Бренд: Gardner Denver Страницы: 22

Бренд: B&G Страницы: 2

Бренд: Ublox Страницы: 2

Бренд: u-blox Страницы: 19

Бренд: Uniden Страницы: 28

Бренд: UniFocus Страницы: 23

Бренд: UniFocus Страницы: 6

PDS CONTROL Series

Бренд: S&P Страницы: 32

Бренд: Danfoss Страницы: 16

Consolidated 2900-40 Series

Бренд: Baker Hughes Страницы: 80

Bell & Gossett Technologic PPS

Бренд: Xylem Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды