Endress+Hauser ControlCare SFC162 Скачать руководство пользователя

Страница: 44 / 64

5 Configuring the Field Controller

ControlCare Field Controller: Commissioning and Configuration

Hauser

5.3.9

Discrete Output block

The Discrete Output block is fully configurable and provides characterization for the outgoing signal.
Depending on the value of

OUT_D

the corresponding "True/1" or "False/0" signal is forced at the

electrical output of the connected module relay output module SFC428, SFC432, SFC435 or
SFC438.

Fig. 5-8 Schematic diagram of the Discrete Output block

Procedure

1 In the fieldbus view, right click on the Discrete Output block

Device Tag-DO-n

and select

Off

Line Characterization

. The Characterization dialog opens.

– Press the

ALL

button in the toolbar to display all parameters

2 Expand the

MODE_BLK

node and set the Target Mode to Auto

–

Select the

Target

node then click the

Edit

button

–

Select

Auto

from the drop-down menu, click

End Edit

to confirm the selection

–

Click

Close

to leave the dialog.

3 Set

CHANNEL

to the input connected to the block as defiined in Section 5.3.1

–

Select

CHANNEL

, then click the

Edit

button

–

Enter the CHANNEL value (Rack+Slot+Group+Slot)

–

Click on

End Edit

4 If you want to invert the signal do it as follows:

–

Select the

IO_OPTS

parameter and click on

Edit

–

Select the

Invert

option and click

End Edit

5 For a delayed output on recognition of a fault, use the

FSTATE_TIME

parameter

–

Select the

FSTATE_TIME

parameter and click on

Edit

–

Enter the delay time (s) then click on

End Edit

6 Repeat the process for all inputs to DO blocks

Properties

The DO block forces the output signals as shown in Table 5-7. NO (Normally open) and NC
(normally closed) is the state of the relay when power is not applied.

Tab. 5-7: Relay status of the output module as a function of OUT_D

BKCAL_OUT

OUT_D

CAS_IN_D

SETPOINT

SP_D

CHANNEL

(RRSGP)

SIMULATE_D

READBACK_D

MODE

SHED_OPS

OPTIONAL

INVERT

FSTATE_TIME

FSTATE_VAL_D

PV_D

OUTPUT

OPTIONAL

INVERT

To module

SFC428
SFC432
SFC435
SFC438

OUT_D

SFC428, SFC432, SFC438
(NO relay)

SFC435, SFC438
(NC relay)

Activated

Deactivated

Activated

Содержание ControlCare SFC162

































































Результаты поиска

Содержание ControlCare SFC162

Отзывы:

Похожие инструкции для ControlCare SFC162

Бренды по названию

Популярные бренды

Endress+Hauser ControlCare SFC162, Руководство по эксплуатации

Результаты поиска

Содержание ControlCare SFC162

Отзывы:

Похожие инструкции для ControlCare SFC162

Бренды по названию

Популярные бренды