Endress+Hauser analytikjena SPECORD PLUS Скачать руководство пользователя страница 36

Страница: 36 / 45

Transport and storage

SPECORD PLUS

Transport and storage

8.1

Moving the device in the laboratory

CAUTION

Risk of injury during transport

Dropping the device poses a risk of injury and damage to the device.

Proceed carefully when moving and transporting the device. Two persons are re-
quired to lift and carry the device.

Grip the device firmly at the bottom with both hands and lift it simultaneously.

Observe the following when moving the device within the laboratory:

Insufficiently secured components pose a risk of injury!
Before moving the device, remove all loose parts and disconnect all connections
from the device.

For safety reasons, two persons are required to transport the device, one person on
each side of the device.

As the device does not have carrying handles, grip the device firmly with both hands
at the lower end. Lift the device simultaneously.

Observe the guide values and adhere to the legally mandated limits for lifting and
carrying loads without auxiliary means.

Observe the installation conditions at the new location.

8.2

Transport

When transporting the device, observe the safety instructions in the "Safety instructions"
section.

Avoid the following during transport:

Impact and vibration
Risk of damage due to shock, impact or vibration!

Large temperature fluctuations
Risk of condensation!

8.3

Storage

NOTICE

Risk of device damage due to environmental conditions

Environmental influences and condensation can destroy individual components of the
device.

Only store the device in air-conditioned rooms.

Ensure that the atmosphere is free of dust and corrosive vapors.

Содержание analytikjena SPECORD PLUS














































Результаты поиска

Содержание analytikjena SPECORD PLUS

Отзывы:

Похожие инструкции для analytikjena SPECORD PLUS

Бренды по названию

Популярные бренды

Endress+Hauser analytikjena SPECORD PLUS, Руководство по эксплуатации

Результаты поиска

Содержание analytikjena SPECORD PLUS

Отзывы:

Похожие инструкции для analytikjena SPECORD PLUS

Бренды по названию

Популярные бренды