background image

9  Start Printing

Before printing, please check the printer again following these steps:

When the printer is powered off:

1.The nozzle is tightly connected and moves smoothly to the left and right.
2.The X axis is horizontal and stable (not wobbling up or down), and it moves run smoothly up and down.
3.The Y axis is tightly connected. The platform does not shake and moves back and forth smoothly.

4.The filament rack does not shake. The rollers are smooth. The filament extrusion is smooth.

When the printer is powered on:
1.The screen display and knob work properly. The movements of the X, Y, and Z axes are smooth.
2.The nozzle and hotbed heat up properly.

3.The feed and return of the filament works properly.

10  About the Printer

1

Material Barrel

2

Z-axis left profile

3

Printhead kit

4

Rack

5

USB Port

6

TF Card Port

7

20 Profile end cap

8   

Z-axis right profile

 

Power supply module

10

Z-axis passive component

11

X adjusting component

12

Display Screen

13

Belt

14

Base component

15

Top gantry profile

16

Screw rod

18

Extrusion kit

19

Z-Axis Limit Switch

20

Z-Axis Motor

17

X-axis profile

16

15

4

5

6

3

2

9

13

7

12

10

8

11

1

20

19

14

18

17

Содержание Ender-3 E













Отзывы: