Empire FAW55IPXLP-1, Инструкция по установке и руководство пользователя

Страница: 9 / 40

37405-0-0616 Page 9
Vent Safety Shutoff System
This appliance must be properly connected to a venting system.
This appliance is equipped with a vent safety shutoff system.
Warning: Operation of this wall furnace when not connected
to a properly installed and maintained venting system or
tampering with the vent safety shutoff system can result in
carbon monoxide (CO) poisoning and possible death.
This furnace is equipped with a manual reset vent safety switch.
The manual reset vent safety switch will cause gas flow to the main
burners to “shut off” due to improper venting or a blocked flue.
To reset the manual reset vent safety switch:
1. Remove upper front panel.
2. Depress red manual reset button. The manual reset vent
safety switch is located on the draft diverter.
3. Replace upper front panel.
If the manual reset vent safety switch continues to “shut off” the
gas flow to the main burners a qualified service person must be
contacted to inspect for improper venting, blockage in the vent pipe
or the manual reset vent safety switch for being defective.
Wiring
The appliance, when installed, must be electrically grounded in
accordance with local codes or, in the absence of local codes, with
the National Electrical Code, ANSI/NFPA 70 or Canadian Electrical
Code, CSA C22.1
, if an external electrical source is utilized. This
appliance is equipped with a three-prong [grounding] plug for
your protection against shock hazard and should be plugged
directly into a properly grounded three-prong receptacle. Do
not cut or remove the grounding prong from this plug. For an
ungrounded receptacle, an adapter, which has two prongs and a
wire for grounding, can be purchased, plugged into the ungrounded
receptacle and its wire connected to the receptacle mounting screw.
With this wire completing the ground, the appliance cord plug can
be plugged into the adapter and be electrically grounded. A 7/8”
(22mm) hole is provided in the junction box for use with a conduit
connector if local codes require this type of protection.
To Conserve Gas: Turn off pilot when heater is not in use.
Insulated Vent Enclosure
Vented wall furnaces installed in buildings with flat roofs can have
poor venting. The cold vent pipe will have a delay in proper venting
and cause the wall furnace to shut “OFF” by the vent safety switch.
To prevent delayed venting as well as condensation of flue products
an insulated vent enclosure is recommended.
Use type B vent pipe and maintain at least a one inch (25mm)
clearance to combustibles.
Use metal thimble to protect vent pipe as it passes through
combustibles.
Installing the
ON/OFF Device
To install an ON/OFF
device (such as a
wall switch, remote,
toggle switch, or
thermostat), remove
the wire nut from the
two wires from the
valve. Run additional
wire from the valve
wires to the ON/
OFF device. Install
the ON/OFF device
in the same room as
the furnace following
the installation
instructions supplied
with it. In the absence
of instructions, install
the ON/OFF device
4 to 5 feet above the
floor on an interior
wall not affected
by another heating
source (i.e. stove or
water heater) or the
temperature of an
adjoining room.
INSTALLATION
Figure 9 Figure 10
IF ANY OF THE ORIGINAL WIRE AS SUPPLIED
WITH THIS UNIT MUST BE REPLACED, IT MUST
BE REPLACED WITH 150°C THERMOPLASTIC
4/64 THICK OR ITS EQUIVALENT.
120V. 60Hz. LESS THAN 3 AMPS
S´IL Y A UN FIL ORIGINAL FOURNI AVEC
L´APPAREIL QUI DIOT ÊTRE REMPLACÉ. IL DOIT
ÊTRE REMPLACÉ AVEC UN FIL
THERMOPLASTIQUE 150°C.
120V. 60Hz. MOINS DE 3 AMPS.
—————— ———————————————————— ———————————————————————————
WHITE (BLANC)
LOW VOLTAGE (BAS VOLTAGE)
120 VOLTS
120 VOLTS
SCHEMATIC WIRING DIAGRAM
——————————————————————————————
SCHÉMA É INSTALLATION LECTRIQUE
JUNCTION BOX
—— —— ——— ———— —————————— — —
BOÎTE DE JONCTION
LIMIT CONTROL
——— — ———— ——————————— —
CONTROL DE
TOLERANCE
AUTO FAN
——— —— ———— ——————— —
VENTILATE
AUTO
TRANSFORMER
——— —— ———— —————————————— —
TRANSFORMATEUR
SPT-3 CORDSET
——— —— ———— ——————————— —
CORDON SPT-3
BLACK (NOIR)
LADDER WIRING DIAGRAM
——————————————————————————
DIAGRAMME À L´ÉCHELLE
D´INSTALLATION ÉLECTRIQUE
YELLOW
——— — ————————
JAUNE
WHITE
——— — ————————
BLANC
BLACK
——— — ————————
NOIR
RED
—
ROUGE
WHT
—
BLANC
TRANSFORMER
——— —— ———— —————————————— —
TRANSFORMATEUR
24 VOLTS
MOTOR
————— ———— —
MOTEUR
AUTO FAN
——— —— ———— ——————— —
VENTILATEUR
AUTO
MOTOR
————— ———— —
MOTEUR
VENT SAFETY
——— — ———— ——————————— —
SÛERTÉ DE
L’ÉVENT
BRN/Brun
WHT/Blanc
RED/Rouge
GRN/Vert
MV
MV/PV
PV
GRND
GAS VALVE
——— — ———— ——————————— —
VALVE DE GAZ
MODULE
VENT SAFETY
——— — ———— ——————————— —
SÛERTÉ DE
L’ÉVENT
GAS VALVE
——— — ———— ——————————— —
VALVE DE GAZ
BRN/Brun
MODULE
WHT/Blanc
RED/Rouge
GRN/Vert
MV
MV/PV
PV MV
MV/PV
PV
GRND
24V
24V
LIMIT CONTROL
——— — ———— ——————————— —
CONTROL DE
TOLERANCE
ON/OFF DEVICE
——— — ———— ——————————— —
ON/OFF
PÉRIPHÉRIQUES
WIRE
NUT
— — ———— ——————— —
FILS
TORSADÉS
WIRE NUT
— — ———— ———————---------------- —
FILS TORSADÉS
ON/OFF DEVICE
——— — ———— ——————————— —
ON/OFF
PÉRIPHÉRIQUES
(3m)
(.6m)
(3m)
More than 10”
Figure 8