background image

30786-7-0415

Page 47

the fireplace will light and operate satisfactorily.
Subsequent lightings of the appliance will not require such purging 

if the gas valve is not turned to “OFF.”

pilot Flame (Figure 65)

The thermopile/thermocouple (standing pilot) tips should be covered 

with flame. 

THERMOCOUPLE

PILOT ASSEMBLY

THERMOPILE

Figure 65

750 Millivolt system

The standing pilot (750 millivolt system) is a continuous burning pilot. 

The pilot remains ON even when the main burner is OFF.
When you ignite the pilot, the thermopile produces millivolts (electrical 

current) which energizes the magnet in the gas valve. After 30 

seconds to 1 minute time period you can release the gas control 

knob and the pilot will stay ON. Allow your pilot flame to operate an 

additional one (1) to two (2) minutes before you turn the gas control 

knob from the PILOT position to the ON position. This time period 

allows the millivolts (electrical current) to build-up to a sufficient 

level allowing the gas control to operate properly.
1.  Follow the SAFETY and LIGHTING INSTRUCTIONS for standing 

pilot controls found in this manual and on labels found in control 

compartment behind the door assembly.

cAUtiOn: During the initial purging and subsequent lightings, 

never allow the gas valve control knob to remain depressed in 

the “pilot” position without pushing the piezo ignitor button at 

least once every second. 

2.  During the operating season, leave the control valve knob in the 

“ON” position. This will allow the pilot flame to remain lit. Turn 

the burner flame on or off with the fireplace REMOTE/OFF/ON 

switch, wall switch or remote controls.

nOte:

 The gas control valve allows you to increase or decrease the 

height of the main burner flame. The control valve has a pressure 

regulator with a knob as shown in Figure 64. Rotate the knob 

clockwise to “HI” to increase the flame height and counterclockwise 

to “LO” to decrease the flame height.
3.  When the operating season is over, turn the REMOTE/OFF/ON 

switch to “OFF” and the control valve to “OFF”. The system, 

including the pilot light, will be shut down.

CONTROL KNOB

HI/LO REGULATOR

Figure 64

The OWNER should carefully read and follow these operating 

instructions at all times. Lower the door assembly to view the gas 

controls for the fireplace.  

initial Lighting

Upon completing the gas line or turning the gas valve on after it has 

been in the “OFF” position, a small amount of air will be in the lines. 

When first lighting the fireplace, it will take a few minutes for the 

lines to purge themselves of this air. Once the purging is complete, 

OperAtinG instrUctiOns

Содержание DVP36PP32EN-3

































































Отзывы: