background image

30786-7-0415

Page 13

GAs sUppLY

The gas pipeline can be brought in through the right or left side of 

the appliance. Consult the current National Fuel Gas Code, ANSI 

Z223.1 CAN/CGA-B149 (.1 or .2) installation code.

recommended Gas pipe Diameter

pipe Length

schedule 40 pipe 

inside Diameter

tubing, type L

Outside Diameter

Nat.

L.P.

Nat.

L.P.

0-10ft

0-3m

1/2"

12.7mm

3/8"

9.5mm

1/2"

12.7mm

3/8"

9.5mm

11-40ft

4-12m

1/2"

12.7mm

1/2"

12.7mm

5/8"

15.9mm

1/2"

12.7mm

41-100ft

13-30m

1/2"

12.7mm

1/2"

12.7mm

3/4"

19mm

1/2"

12.7mm

101-150ft

31-46m

3/4"

19mm

1/2"

12.7mm

7/8"

22.2mm

3/4"

1.9 mm

note:

 Never use plastic pipe. Check to confirm whether your 

local codes allow copper tubing or galvanized.

note:

 Since some municipalities have additional local codes, it is 

always best to consult your local authority and installation code.
The use of the following gas connectors is recommended:
—  ANS Z21.24 Appliance Connectors of Corrugated Metal Tubing 

and Fittings.

—  ANS Z21.45 Assembled Flexible Appliance Connectors of Other 

Than All-Metal Construction

The above connectors may be used if acceptable by the authority 

having jurisdiction. The state of Massachusetts requires that a flexible 

appliance connector cannot exceed three feet in length.

Figure 9

Gas supply pressure (inches w.c.)

Minimum

Normal

Maximum

Natural Gas

4.5"

7.0"

14.0"

LP (Propane)

10.8"

11.0"

14.0"

Manifold Pressure (inches w.c.)

Normal (HI)

Natural Gas

3.5"

LP (Propane)

10.0"

installing a new Main Gas cock

Each appliance should have its own manual gas cock.
A manual main gas cock should be located in the vicinity of the unit. 

Where none exists, or where its size or location is not adequate, 

contact your local authorized installer for installation or relocation.
Compounds used on threaded joints of gas piping shall be resistant 

to the action of liquefied petroleum gases. The gas lines must be 

checked for leaks by the installer. This should be done with a soap 

solution watching for bubbles on all exposed connections, and if 

unexposed, a pressure test should be made. 

never use an exposed flame to check for leaks. Appliance must 

be disconnected from piping at inlet of control valve and pipe 

capped or plugged for pressure test. never pressure test with 

appliance connected; control valve will sustain damage!

nOte: 

The millivolt gas controls are equipped with a captured screw 

type pressure test point, therefore it is not necessary to provide a 

1/8" test point up stream of the control.
When using copper or flex connector use only approved fittings. 
The appliance and it’s individual shut off valve must be disconnected 

from supply piping system during any pressure testing of that system 

at test pressures in excess of 1/2 psig (3.5kPa).
The appliance must be isolated from the gas supply piping system 

by closing its individual manual shut off valve during any pressure 

testing of the gas supply piping system at test pressures equal to 

or less than 1/2 psig (3.5kPa).

Attention!

 If one of the procedures results in pressures in excess of 

1/2 psig (14" w.c.) (3.5 kPa) on the fireplace gas valve, it will result 

in a hazardous condition.

checking Manifold pressures

Both Propane and Natural gas valves have a built-in pressure 

regulator in the gas valve. Natural gas models will have a manifold 

pressure of approximately 3.5" w.c. (.871kPa) at the valve outlet 

with the inlet pressure to the valve from a minimum of 4.5" w.c. 

(1.120kPa) for the purpose of input adjustment to a maximum of 

14.0" w.c. (3.484kPa). Propane gas models will have a manifold 

pressure approximately 10.0" w.c. (2.49kPa) at the valve outlet 

with the inlet pressure to the valve from a minimum of 10.8" w.c. 

(2.68kPa) for the purpose of input adjustment to a maximum of 

14.0" w.c. (3.484kPa).  

ELECTRICAL ACCESS

GAS LINE ACCESS

4 1/8”

2 3/8”

5 1/2”

5 7/8”

Figure 10

Содержание DVP36PP32EN-3

































































Отзывы: