Empire Comfort Systems MILLIVOLT DVD32FP30N-3 Скачать руководство пользователя страница 4

43115-2-0821

43115-2-0821

Page 4

SAFETY INFORMATION FOR USERS OF PROPANE GAS

Propane is a flammable gas which can cause fires and 

explosions. In its natural state, propane is odorless and 

colorless. You may not know all the following safety 

precautions which can protect both you and your family 

from an accident. Read them carefully now, then review 

them point by point with the members of your house

-

hold. Someday when there may not be a minute to lose, 

everyone’s safety will depend on knowing exactly what 

to do. If, after reading the following information, you feel 

you still need more information, please contact your gas 

supplier.

PROPANE GAS WARNING ODOR

If a gas leak happens, you should be able to smell the 

gas because of the odorant put in the Propane Gas. 

That’s your signal to go into immediate action!

•  Do not operate electric switches, light matches, use your 

phone. Do not do anything that could ignite the gas.

•   Get everyone out of the building, vehicle, trailer, or area. 

Do that IMMEDIATELY.

•   Close all gas tank or cylinder supply valves.

•   Propane Gas is heavier than air and may settle in low 

areas such as basements. When you have reason to 

suspect a gas leak, keep out of basements and other 

low areas. Stay out until firefighters declare them to be 

safe.

•   Use your neighbor’s phone and call a trained Propane 

Gas service person and the fire department. Even though 

you may not continue to smell gas, do not turn on the 

gas again. Do not re-enter the building, vehicle, trailer, 

or area.

• 

 Finally,

 let the service man and firefighters check for 

escaped gas. Have them air out the area before you 

return. Properly trained Propane Gas service people 

should repair the leak, then check and relight the gas 

appliance for you.

NO ODOR DETECTED - ODOR FADE

Some people cannot smell well. Some people cannot 

smell the odor of the chemical put into the gas. You 

must find out if you can smell the odorant in propane.

 

Smoking can decrease your ability to smell. Being around an 

odor for a time can affect your sensitivity or ability to detect 

that odor. Sometimes other odors in the area mask the gas 

odor. People may not smell the gas odor or their minds are 

on something else. Thinking about smelling a gas odor can 

make it easier to smell.

The odorant in Propane Gas is colorless, and it can fade 

under some circumstances.

 For example, if there is an 

underground leak, the movement of the gas through soil can 

filter the odorant. Odorants in Propane Gas also are subject 

to oxidation. This fading can occur if there is rust inside the 

storage tank or in iron gas pipes.

The odorant in escaped gas can adsorb or absorb onto or 

into walls, masonry and other materials and fabrics in a room. 

That will take some of the odorant out of the gas, reducing 

its odor intensity.

Propane Gas may stratify in a closed area, and the odor inten-

sity could vary at different levels. Since it is heavier than air, 

there may be more odor at lower levels. Always be sensitive 

to the slightest gas odor. If you detect any odor, treat it as a 

serious leak. Immediately go into action as instructed earlier.

SOME POINTS TO REMEMBER

• 

Learn to recognize the odor of Propane Gas.

 Your 

local Propane Gas Dealer can give you a “Scratch and 

Sniff” pamphlet. Use it to find out what the propane odor 

smells like. If you suspect that your Propane Gas has a 

weak or abnormal odor, call your Propane Gas Dealer.

•  If you are not qualified, do not light pilot lights, perform 

service, or make adjustments to appliances on the Pro

-

pane Gas system. If you are qualified, consciously think 

about the odor of Propane Gas prior to and while lighting 

pilot lights or performing service or making adjustments.

•  Sometimes a basement or a closed-up house has a musty 

smell that can cover up the Propane Gas odor. Do not try 

to light pilot lights, perform service, or make adjustments 

in an area where the conditions are such that you may not 

detect the odor if there has been a leak of Propane Gas.

•  Odor fade, due to oxidation by rust or adsorption on walls 

of new cylinders and tanks, is possible. Therefore, people 

should be particularly alert and careful when new tanks 

or cylinders are placed in service. Odor fade can occur 

in new tanks, or reinstalled old tanks, if they are filled 

and  allowed  to  set  too  long  before  refilling.  Cylinders 

and tanks which have been out of service for a time 

may develop internal rust which will cause odor fade. If 

such conditions are suspected to exist, a periodic sniff 

test of the gas is advisable. 

If you have any question 

about the gas odor, call your Propane Gas Dealer. 

A periodic sniff test of the Propane Gas is a good 

safety measure under any condition.

•  If, at any time, you do not smell the Propane Gas odorant 

and you think you should, assume you have a leak. Then 

take the same immediate action recommended above for 

the occasion when you do detect the odorized Propane Gas.

•  If you experience a complete “gas out,” (the container 

is under no vapor pressure), turn the tank valve off im-

mediately. If the container valve is left on, the container 

may draw in some air through openings such as pilot light 

orifices. If this occurs, some new internal rusting could 

occur. If the valve is left open, then treat the container 

as a new tank. Always be sure your container is under 

vapor pressure by turning it off at the container before 

it goes completely empty or having it r

efilled before it is 

completely empty.

Содержание MILLIVOLT DVD32FP30N-3





































































Отзывы: