manualshive.com logo in svg

Empire Comfort Systems MILLIVOLT DVD32FP30N-3, Руководство по установке, Страница: 37 / 68

Поделиться
Скачать
Empire Comfort Systems MILLIVOLT DVD32FP30N-3 Скачать руководство пользователя страница 37

Page 37

43115-2-0821

43115-2-0821

Figure 57

Warning: Failure to position the parts in accordance with this 

diagram or failure to use only parts specifically approved 

with this appliance may result in property damage or 

personal injury. 

Attention: Do not use 

Figure 57 or Figure 58

 to order logs. Refer 

to parts lists and parts views on pages 60 to 63 to order logs and/

or ember material for your appropriate fireplace model. 

This fireplace is supplied with a set of seven ceramic fiber logs. Do 

not handle these logs with your bare hands. Always wear gloves to 

prevent skin irritation from ceramic fibers. After handling logs, wash 

your hands gently with soap and water to remove any traces of fiber.

The positioning of logs is critical to safe and clean operation of this 

fireplace. Sooting and other problems may result if the logs are not 

properly and firmly positioned in the fireplace. Please refer to 

Figure 

57

 

and

 

Figure 58

 and corresponding WARNING when completing 

following log placement steps.
1.  Remove top louver, grasp louver, lift and pull forward.

2.  Lower bottom louver, lift and hinge forward.

3.  Release two glass frame spring clamps at bottom of firebox

4.  Remove glass frame spring assembly.

5.  Place front logs (#1, #2, and #3) between grates and main 

burner. Align notches on front logs with locator tabs in base.

6.  Place middle log (#4) between front and rear loop of burner. 

Note: do not place on top of pilot assembly.

7.  Place rear log (#5) on rear log shelf. Bottom flange is to be 

placed between the log shelf and burner tube.

8.  Place bottom "Y" branch (#6) onto flat areas of middle log (#4) 

and bottom end of "Y" branch to the back side of the grate tang 

(4th one from the left).

9.  Place top branch (#7) onto flat area of rear log (#5) and over 

the front of "Y" branch.

10.  Place decorative rock in front of grates and sides of main burner.

ATTENTION

: Do not place decorative rock on logs or on burner. 

The decorative rock should only be placed on the fireplace floor.

11.  After all logs are properly positioned, place small "dime" size 

pieces of Rockwool lightly across the front burner tube ports. 

Place the ember material (Rockwool pieces) side by side. Do 

not stack more than one layer of embers across the burner 

ports. 

See Figure 58.

12.  Replace glass frame onto firebox.

13.  Secure the two glass frame spring clamps at bottom of firebox.

14.  Align the tabs on top louver brackets with slots in front posts 

to secure top louver.

15.  Close bottom louver. Lift slightly to engage the end tabs into 

the slots in fireplace sides to close louver panel.

LOG PLACEMENT (7 LOG SET) - DVD(42,48)FP

Figure 58

Содержание MILLIVOLT DVD32FP30N-3





































































Отзывы:

Нет отзывов