manualshive.com logo in svg
background image

The Heritage Cast Iron Stoves

INSTALLATION INSTRUCTIONS

AND 

OWNER'S MANUAL

This appliance may be installed in an aftermarket 

permanently located, manufactured home (USA 

only)  or  mobile  home,  where  not  prohibited  by 

local codes.
This appliance is only for use with the type of gas 

indicated  on  the  rating  plate.  This  appliance  is 

not convertible for use with other gases, unless a 

certified kit is used.

WARNING:  Improper  installation,  adjustment, 

alteration, service or maintenance can cause injury 

or property damage. Refer to this manual. For assis-

tance or additional information consult a qualified 

installer, service agency, or the gas supplier.

CAST IRON

DIRECT VENT STOVE 

MODELS:

DVP30CA30(B,F,M,S,W)N-1

DVP30CA30(B,F,M,S,W)P-1

—  Do  not  store  or  use  gasoline  or  other 

flammable vapors and liquids in the vicinity 

of this or any other appliance.

—  WHAT TO DO IF YOU SMELL GAS

  •  Do not try to light any appliance.

  •  Do not touch any electrical switch; do not 

use any phone in your building.

  •  Immediately call your gas supplier from a 

neighbor’s phone. Follow the gas suppli-

er’s instructions.

  •  If you cannot reach your gas supplier, call 

the fire department.

—  Installation  and  service  must  be  performed 

by a qualified installer, service agency or the 

gas supplier.

WARNING: If the information in these instruc-

tions are not followed exactly, a fire or explosion 

may result causing property damage, personal 

injury or loss of life.

Installer:  Leave this manual with the appli-

ance.

Consumer: Retain this manual for future refer-

ence.

EMPIRE

EMPIRE

Comfort Systems

GAS-FIRED

Page 1

Содержание DVP30CA30B-N1









































Отзывы: