manualshive.com logo in svg

Empire Comfort Systems DVLXB55BP90N-1, Руководство по установке, Страница: 52 / 66

Поделиться
Скачать
Empire Comfort Systems DVLXB55BP90N-1 Скачать руководство пользователя страница 52

52

Problem Observed

Possible Cause

Corrective Measure

Burner and pilot light but will 

not stay lit

Flame sensor dirty

Clean pilot sensor

Low gas pressure

Check gas supply pressure

Not enough fresh air for pilot

Open door or window -ventilate the room

Clogged or dirty burner ports

Clean burner ports

Room temperature is higher than 

thermostat setting

Move remote away from the fireplace

Set higher temperature on remote/thermostat

Remote control batteries failing

Replace batteries in remote transmitter and 

receiver

Faulty pilot or thermocouple

Replace pilot

Incorrect burner flame

Incorrect gas supply or pressure

Check gas supply pressure

Blocked orifice

Check orifice opening

Clogged or dirty burner ports

Clean burner ports

Faulty valve

Replace valve

High altitude

Adjust orifice size for altitude

Backfire of burner

Blocked orifice

Check orifice opening

Clogged or dirty burner ports

Clean burner ports

Low gas pressure

Check gas supply pressure

Fireplace produces unwanted 

odors

Vapors from paint, hairspray, glue, etc.

Ventilate room until odor stops. Do not use paint, 

hairspray, glue, etc. around the fireplace

Initial burn off of manufacturing 

chemicals

Ventilate room until odor stops

Whistle noise from fireplace

Check gas pressure

Adjust gas pressure to recommended settings

Air in gas line

Bleed lines

Control knob not in fully open position

Open control knob to full position

Spiral gas flex line pinched or too small 

diameter line

Straighten flex line where pinched or replace gas 

feed line with larger diameter

CONTROL SYSTEM TROUBLESHOOTING (CONT’D)

Содержание DVLXB55BP90N-1



































































Отзывы:

Нет отзывов