Empire Comfort Systems DVL36BP30 Series Скачать руководство пользователя страница 5

41978-1-1220

Page 5

SAFETY INFORMATION FOR USERS OF PROPANE GAS

Propane is a flammable gas which can cause fires and 

explosions. In its natural state, propane is odorless and 

colorless. You may not know all the following safety 

precautions which can protect both you and your family 

from an accident. Read them carefully now, then review 

them point by point with the members of your household. 

Someday when there may not be a minute to lose, everyone’s 

safety will depend on knowing exactly what to do. If, after 

reading the following information, you feel you still need 

more information, please contact your gas supplier.
PROPANE GAS WARNING ODOR

If a gas leak happens, you should be able to smell the gas 

because of the odorant put in the Propane Gas. That’s your 

signal to go into immediate action!

• 

Do not operate electric switches, light matches, use your 

phone. Do not do anything that could ignite the gas.

•   Get everyone out of the building, vehicle, trailer, or area. Do 

that IMMEDIATELY.

•   Close all gas tank or cylinder supply valves.
•   Propane Gas is heavier than air and may settle in low areas 

such as basements. When you have reason to suspect a gas 

leak, keep out of basements and other low areas. Stay out 

until firefighters declare them to be safe.

•   Use your neighbor’s phone and call a trained Propane Gas 

service person and the fire department. Even though you 

may not continue to smell gas, do not turn on the gas again. 

Do not re-enter the building, vehicle, trailer, or area.

•  

Finally, 

let the service man and firefighters check for 

escaped gas. Have them air out the area before you return. 

Properly trained Propane Gas service people should repair 

the leak, then check and relight the gas appliance for you.

NO ODOR DETECTED - ODOR FADE

Some people cannot smell well. Some people cannot smell 

the odor of the chemical put into the gas. You must find 

out if you can smell the odorant in propane.

 Smoking can 

decrease your ability to smell. Being around an odor for a time 

can affect your sensitivity or ability to detect that odor. Sometimes 

other odors in the area mask the gas odor. People may not smell 

the gas odor or their minds are on something else. Thinking 

about smelling a gas odor can make it easier to smell.

The odorant in Propane Gas is colorless, and it can fade 

under some circumstances. 

For example, if there is an 

underground leak, the movement of the gas through soil can 

filter the odorant. Odorants in Propane Gas also are subject to 

oxidation. This fading can occur if there is rust inside the storage 

tank or in iron gas pipes.
The odorant in escaped gas can adsorb or absorb onto or into 

walls, masonry and other materials and fabrics in a room. That will 

take some of the odorant out of the gas, reducing its odor intensity.

Propane Gas may stratify in a closed area, and the odor intensity 

could vary at different levels. Since it is heavier than air, there 

may be more odor at lower levels. Always be sensitive to the 

slightest gas odor. If you detect any odor, treat it as a serious 

leak. Immediately go into action as instructed earlier.

SOME POINTS TO REMEMBER

• 

Learn to recognize the odor of Propane Gas. Your local 

Propane Gas Dealer can give you a 

Scratch and Sniff

 

pamphlet. Use it to find out what the propane odor smells 

like. If you suspect that your Propane Gas has a weak or 

abnormal odor, call your Propane Gas Dealer.

• 

If you are not qualified, do not light pilot lights, perform 

service, or make adjustments to appliances on the Propane 

Gas system. If you are qualified, consciously think about the 

odor of Propane Gas prior to and while lighting pilot lights or 

performing service or making adjustments.

• 

Sometimes a basement or a closed-up house has a musty 

smell that can cover up the Propane Gas odor. Do not try to 

light pilot lights, perform service, or make adjustments in an 

area where the conditions are such that you may not detect 

the odor if there has been a leak of Propane Gas.

• 

Odor fade, due to oxidation by rust or adsorption on walls 

of new cylinders and tanks, is possible. Therefore, people 

should be particularly alert and careful when new tanks or 

cylinders are placed in service. Odor fade can occur in new 

tanks, or reinstalled old tanks, if they are filled and allowed 

to set too long before refilling. Cylinders and tanks which 

have been out of service for a time may develop internal rust 

which will cause odor fade. If such conditions are suspected 

to exist, a periodic sniff test of the gas is advisable.

 If you 

have any question about the gas odor, call your Propane 

Gas Dealer. A periodic sniff test of the Propane Gas is a 

good safety measure under any condition.

• 

If, at any time, you do not smell the Propane Gas odorant 

and you think you should, assume you have a leak. Then 

take the same immediate action recommended above for the 

occasion when you do detect the odorized Propane Gas.

• 

If you experience a complete 

gas out,

 (the container 

is under no vapor pressure), turn the tank valve off 

immediately. If the container valve is left on, the container 

may draw in some air through openings such as pilot light 

orifices. If this occurs, some new internal rusting could occur. 

If the valve is left open, then treat the container as a new 

tank. Always be sure your container is under vapor pressure 

by turning it off at the container before it goes completely 

empty or having it refilled before it is completely empty.

Содержание DVL36BP30 Series





































































Отзывы: