background image

Page 1

INSTALLATION INSTRUCTIONS

This appliance may be installed in an 

aftermarket, permanently located, 

manufactured home (USA only) or mobile 

home, where not prohibited by local codes.
This appliance is only for use with the type 

of gas indicated on the rating plate. 
This appliance is not convertible for use with 

other gases, unless a certified kit is used.

WARNING

If not installed, operated and maintained 

in accordance with the manufacturer’s 

instructions, this product could expose you 

to substances in fuel or from fuel combustion 

which can cause death or serious illness.

WARNING

FIRE OR EXPLOSION HAZARD

Failure to follow safety warnings exactly 

could result in serious injury, death or 

property damage.

—  Do not store or use gasoline or other 

flammable vapors and liquids in the 

vicinity of this or any other appliance.

—  WHAT TO DO IF YOU SMELL GAS

•  Do not try to light any appliance.

•  Do not touch any electrical switch; 

do not use any phone in your building.

•  Leave the building immediately.

•  Immediately call your gas supplier 

from a neighbor’s phone. Follow 

the gas supplier’s instructions.

•  If you cannot reach your gas 

supplier, call the fire department.

—  Installation and service must be 

performed by a qualified installer, 

service agency or the gas supplier.

INSTALLER: 

Leave this manual with the appliance.

CONSUMER: 

Retain this manual for future reference.

DIRECT-VENT 

GAS FIREPLACE 

HEATER MODEL 

SERIES:

MV CONTROL

DVL(36,46)BP30(N,P)-1

IP CONTROL

DVL(36,46)BP70(N,P)-1

GAS-FIRED

UL FILE NO. 

MH30033

Содержание DVL36BP30 Series





































































Отзывы: