Empire Comfort Systems DVCT40CSP95N-1 Скачать руководство пользователя страница 36 | Manualshive

Страница: 36 / 52

Empire Comfort Systems DVCT40CSP95N-1 Скачать руководство пользователя страница 36

40651-2-0320

Page 36

MULTIFUNCTION REMOTE OPERATING INSTRUCTIONS

Continuous Pilot/ Intermittent Pilot (CPI/IPI) Selection

With the system in “OFF” position press the Mode Button

Figure

3

to index to the CPI mode icon.

See Figures 80 and 81.

Pressing the Up Arrow Button will activate the (CPI). Pressing the

Down Arrow Button will return to IPI. A single “beep” will confirm

the reception of the command.

OFF

Figure 80

OFF

Figure 81

Button Lock

T

his function will lock the Buttons to avoid unsupervised operation.

To activate this function, press the MODE and UP Buttons at the

same time.

See Figure 82.

To deactivate this function, press the MODE and UP Buttons at

the same time.

OFF

Figure 82

Low Battery Power Detection - Transmitter

The life span of the remote control batteries depends on various

factors: quality of the batteries used, the number of ignitions of

the appliance, the number of changes to the room thermostat set

point, etc.

When the transmitter batteries are low, an Icon will appear on the

LCD display of the transmitter

See Figure 83

before all battery pow

-

er is lost. When the batteries are replaced this Icon will disappear.

OFF

Figure 83

«
...
34
35
36
37
38
...
»

Содержание DVCT40CSP95N-1





















































Отзывы:

Нет отзывов