manualshive.com logo in svg

Empire Comfort Systems DVCT40CSP95N-1, Руководство по установке, Страница: 35 / 52

Поделиться
Скачать
Empire Comfort Systems DVCT40CSP95N-1 Скачать руководство пользователя страница 35

40651-2-0320

Page 35

Remote Dimmer Control (Light)

The auxiliary function controls the power light outlet by the 

dimmable light control. To activate this function, use the Mode 

Button 

Figure 57

 to index to the light icon. 

See Figures 74 and 75.

 

The intensity of the output can be adjusted through six levels. Use 

the Up/Down Arrow Buttons 

Figure 57

 to adjust the output level. A 

single “beep” will confirm reception of the command.

NOTE:

 This function is available only with the IFC control Module.

OFF

Figure 74

OFF

Figure 75

Split Flow Control

The secondary burner is controlled by the split Flow. To activate 

this function use the Mode Button 

Figure 57

 to index to the 

SPLIT FLOW mode icon. 

See Figures 76 and 77

.

Pressing the Up Arrow Button will activate the secondary burner. 

Pressing the Down Arrow Button will turn the secondary burner 

off. A single “beep” will confirm the reception of the command.

OFF

Figure 76

MULTIFUNCTION REMOTE OPERATING INSTRUCTIONS

OFF

Figure 77

Remote Auxiliary Relay Control (optional with this fireplace)

The auxiliary function controls the AUX relay outlet. To activate 

this function use the Mode Button 

Figure 57

 to index to the AUX 

icon 

Figures 78 & 79

. Pressing the Up Arrow Button will activate 

the outlet. Pressing the Down Arrow Button will turn the outlet off. 

A single “beep” will confirm the reception of the command.

Figure 78

Figure 79

Содержание DVCT40CSP95N-1





















































Отзывы:

Нет отзывов