Empire Comfort Systems DVCT40CSP95N-1 Скачать руководство пользователя страница 34

Страница: 34 / 52

40651-2-0320

Page 34

MULTIFUNCTION REMOTE OPERATING INSTRUCTIONS

The Thermostat Feature may be disabled if desired.

With all three AAA type batteries installed:

1. Take out one AAA battery.

2. While re-inserting the AAA battery, Push and hold down the

thermostat button. This will disable the thermostat feature on

the transmitter.

Room Thermostat (Transmitter Operation)

The Remote Control can operate as a room thermostat. The ther

mostat can be set to a desired temperature to control the comfort

level in a room. To activate this function, press the Thermostat

Button.

See Figure 57

. The LCD display on the Transmitter will

change to show that the room thermostat is “ON” and the set

temperature is now displayed.

See Figure 68.

To adjust the

set temperature, press the Up or Down Arrow Buttons until the

desired set temperature is displayed on the LCD screen of the

Transmitter.

See Figure 69.

SET TEMPERATURE

ROOM TEMPER ATURE

Figure 68

Figure 69

Smart Thermostat (Transmitter Operation)

The Smart Thermostat function adjusts the flame height in

accordance to the difference between the set point temperature

and the actual room temperatures. As the room temperature gets

closer to the set point the Smart Function will modulate the flame

down. To activate this function, press the Thermostat Button until

the word “SMART” appears to the right of the temperature bulb

graphic.

See Figure 70

. To adjust the set temperature, press the

Up or Down Arrow Buttons until the desired set temperature is

displayed on the LCD screen of the Transmitter.

See Figure 71.

NOTE:

When Smart Thermostat is activated, manual flame

height adjustment is disabled.

Figure 70

Figure 71

Blower Control (Fan)

If the appliance is equipped with a hot air circulating fan, the

speed of the fan can be controlled by the Proflame system. The

fan speed can be adjusted through six speeds. To activate this

function, use the Mode Button

Figure 57

to index the fan control

icon.

See Figure 72

. Use the Up/Down Arrow Buttons

Figure

to turn on off or adjust the fan speed.

See Figure 73

. A single

“beep” will confirm reception of the command.

OFF

Figure 72

OFF

Figure 73

Содержание DVCT40CSP95N-1





















































Результаты поиска

Содержание DVCT40CSP95N-1

Отзывы:

Empire Comfort Systems DVCT40CSP95N-1, Руководство по установке, Страница: 34 / 52

Результаты поиска

Содержание DVCT40CSP95N-1

Отзывы: