Empire Comfort Systems DVCT40CSP95N-1 Скачать руководство пользователя страница 14

Страница: 14 / 52

40651-2-0320

Page 14

NOTICE:

When installing this appliance against an exterior wall,

insulate to applicable insulation codes.

NOTICE:

Island and Room Divider installation is possible as long

as the horizontal portion of the vent system does not exceed 18 feet

with a minimum vertical run of 8 feet. See details in Venting Section.
When you install your Direct Vent Fireplace in room divider or flat

on wall corner positions, maintain a minimum of 6 inches between

the perpendicular wall and the opening of the appliance.

LOCATING FIREPLACE

ROOM DIVIDER

INSTALLATION

FLUSH WALL

INSTALLATION

ISLAND

INSTALLATION

CABINET

INSTALLATION

CORNER

INSTALLATION

Figure 10

ELECTRICAL CONSIDERATIONS

Junction Box

A factory-installed junction box is located on the lower right side of

the fireplace. Wiring must be fed to the junction box and attached

with wire nuts to the control module power leads already fed into

the junction box.
Attach black to black and white to white. The ground wire should be

attached to the ground on the junction box.

See Figure 11.

Interface/Battery Holder

The user interface/battery holder must be mounted within a distance

allowed by the attached 12 foot harness. As shipped, this harness is

already fed through a strain relief on the bottom of the component

access box and is attached to the User Interface/Battery Holder.

NOTICE:

If an auxiliary device is to be used, its wiring may be fed

through the junction box strain relief. Auxiliary device amperage

limit is 5 amps.

NOTICE:

A one inch diameter hole should be use to pass wiring

through studs.

BLACK (HOT)

JUNCTION BOX

WHITE (NEUTRAL)

GROUND TO JUNCTION BOX

120 VOLT POWER SUPPLY

JUNCTION BOX CONNECTIONS

Figure 11

CAUTION

All wiring should be done by a qualified electrician and shall be in compliance with all local, city and state building codes.

Before making the electrical connection, make sure that the main power supply is disconnected. The appliance, when installed,

must be electrically grounded in accordance with local codes, or in the absence of local codes, with the National Electrical

Code ANSI/NFPA 70 (Latest Edition).

VERTICAL

FRAMING

MEMBER

USER INTERFACE
HARNESS

USER INTERFACE/
BATTERY HOLDER
MUST BE INSTALLED
INTO WALL JUNCTION
BOX. (ORANGE LOW-
VOLTAGE BOX
RECOMMENDED.)

ELECTRICAL POWER TO UNIT
JUNCTION BOX / CONTROL MODULE

Figure 12

Содержание DVCT40CSP95N-1





















































Результаты поиска

Содержание DVCT40CSP95N-1

Отзывы:

Empire Comfort Systems DVCT40CSP95N-1, Руководство по установке, Страница: 14 / 52

Результаты поиска

Содержание DVCT40CSP95N-1

Отзывы: