manualshive.com logo in svg

Empire Comfort Systems DVCT40CSP95N-1, Руководство по установке, Страница: 31 / 52

Поделиться
Скачать
Empire Comfort Systems DVCT40CSP95N-1 Скачать руководство пользователя страница 31

40651-2-0320

Page 31

MULTIFUNCTION REMOTE OPERATING INSTRUCTIONS

Figure 56

TECHNICAL DATA

Remote Control

Supply voltage

4.5 V (three 1.5 V AAA batteries)

Ambient temperature ratings

0-50°C (32 - 122°F)

Radio frequency

315 MHz

WARNING

The transmitter and receiver are radio frequency devices. 

Placing the receiver in or near metal may severely reduce 

the signal range.

WARNING

Turn “off” the main gas supply and electrical supply to the 

appliance during installation and/or maintenance of the 

receiver device.

WARNING

FIRE HAZARD. CAN CAUSE SEVERE INJURY OR DEATH.

The Receiver causes ignition of the appliance. The appliance 

can turn on suddenly. Keep away from the appliance burner 

when operating the remote system or activating manual 

bypass of the remote system.

CAUTION

PROPERTY DAMAGE HAZARD.

EXCESSIVE HEAT CAN CAUSE PROPERTY DAMAGE.

The appliance can stay lit for many hours. Turn off the 

appliance if it is not going to be attended for any length of 

time. Always place the Transmitter where children can not 

reach it.

Figure 57

NOTE:

 This control system includes a Battery Back-up pack that 

allows the Fireplace to operate in the event of a power outage.

NOTE:

 The Accent Light and/or Blower features will not operate 

during a power outage.

NOTE:

 Replace all Batteries at least once each year, preferably 

before at the beginning of the season.

CAUTION

FIRE OR EXPLOSION HAZARD.

 

Can cause property damage, sever injury or death. Do not 

attempt to take apart the gas control or to clean it. Improper 

assembly and cleaning can cause unreliable operation.

Содержание DVCT40CSP95N-1





















































Отзывы:

Нет отзывов