Empire Comfort Systems DVCT36CBP Скачать руководство пользователя

Страница: 24 / 48

38745-4-0319

Page 24

SPECIAL vENT SYSTEMS

Figure 47

GeNeRIC moDeL SHoWN

vENT SYSTEM IDENTIFICATION

FLASHING

STORM
COLLAR

VERTICAL
TERMINATION
(THREE 90°
ELBOWS MAX)

WALL THIMBLE

HORIZONTAL TERMINATION
(THREE 90° ELBOWS MAX)

90° ELBOW

45° ELBOW

90° ELBOW

CEILING

FIRE STOP

WALL STRAP

PIPE LENGTH

WALL THIMBLE SPACER
(DVCT36 ONLY)

Special DV Vent Kits

Available from empire Comfort Systems, Inc. dealers.

DVVK-5RP

Direct-Vent Fireplace Vent Kit for Rear Vent, 6

to 12 inch wall thickness, Includes 58DVA-06,

58DVA-WT, and 58DVAHC

DVVK-5TP

Direct-Vent Fireplace Vent Kit for Top Vent,

Thru-the-wall, 4 to 6 inch wall thickness,

Includes 58DVA-e90, 58DVA-HC, 58DVA-06,

and 58DVA-WT

DVVK-5VP

Direct Vent Fireplace Vent Kit - Vertical,

Includes 58DVA-VCH, 58DVA-SC, and

58DVA-F6

DVVK-5TS Top Vent Kit (Horizontal) - 4½" to 6" wall

thickness (114.3 mm to 152 mm)

DVVK-5F

Horizontal Flex Vent Kit (4' Flex) (1.22m)

Begin the vent system installation by selecting the type of venting

to be installed and the path that it will take. Verify that clearances

are met throughout the path of the venting system.

NOTICE:

These fireplaces cannot be vented out the rear.

Determine how the vent system will be terminated out the side of

the house or through the roof. Verify clearances for the termination.
When selecting a vent system for use with the fireplace, refer to the

“Special Vent Systems” section below to determine what systems

are acceptable. Check all clearances and venting components.

Identify if any problems existing in the vent system.

NOTICE:

All outer connection joints must be sealed with aluminum

tape, screws or silicone sealant rated above 300°F/149°C. The inner

flue joints do not require any sealant.

•

Simpson Duravent ® GS 5 inch x 8 inch

•

American metal Products 5 inch x 8 inch

•

Selkirk Direct-Temp ® 5 inch x 8 inch

•

Security Secure Vent ® 5 inch x 8 inch

•

excel DV Venting 5 inch x 8 inch

•

empire Flexvent Kit DVVK-5F

– 6 inch piece of hard pipe is required

(See flex vent instruction section)

•

BDm - 5 inch x 8 inch

•

metal Fab Sure Seal ® 5 inch x 8 inch

– Adapter is required to use this vent

Contact metal Fab

The following vent systems are acceptable for use with the

DvCT36 and

DVCT40 series fireplaces:

Содержание DVCT36CBP

















































Результаты поиска

Содержание DVCT36CBP

Отзывы:

Похожие инструкции для DVCT36CBP

Бренды по названию

Популярные бренды

Empire Comfort Systems DVCT36CBP, Руководство по установке

Результаты поиска

Содержание DVCT36CBP

Отзывы:

Похожие инструкции для DVCT36CBP

Бренды по названию

Популярные бренды