Empire Comfort Systems DVCT36CBP Скачать руководство пользователя

Страница: 7 / 48

38745-4-0319

Page 7

INTRODUCTION

The information in this manual pertains to all models and gas

control systems unless otherwise noted.

Instructions to Installer

1. Leave this manual with Homeowner.

2. Have the homeowner complete the Product Registration

Card or register online at www.empirecomfort.com

3. Show the homeowner how to start and operate the fireplace.

Notes to Installer

•

This fireplace is designed to:

operate with combustion air siphoned from outside of

the building.

expel all exhaust gases to the outside of the building.

•

The installation must conform with local codes or, in the

absence of local codes, with the National Fuel Gas Code

ANSI Z223.1/NFPA 54* Natural Gas and Propane Installation

Code, or CSA B149.1 in Canada. * Available from the

American National Standards Institute, Inc. 11 West 42nd

St., New York, N.Y. 10036

•

Any alteration of the original design, installation other than

as shown in these instructions, or use with a type of gas not

shown on the rating plate is the responsibility of the person

and company making the change.

•

This fireplace is not for use with solid fuels.

•

These fireplace models may be installed in a bedroom or

bed-sitting room in the U.S.A. and Canada.

WARNING

Any change to this fireplace can be dangerous. Improper

installation or use can cause serious injury or death from fire,

burns, explosion or carbon monoxide poisoning.

Fireplace Certification

This fireplace is design certified in accordance with American

National Standard/CSA Standard ANSI Z21.88/CSA 2.33 and by

Underwriters Laboratories as a Direct Vent Gas Fireplace Heater

and shall be installed according to these instructions.

Consult your local building code agency, prior to installation,

to ensure compliance with local codes-including permits and

inspections.

The fireplace, when installed, must be electrically grounded in

accordance with local codes or, in absence of local codes, with

the National electric Code ANSI/NFPA 70 or Canadian electric

code, CSA C22.1, if an external electrical source is utilized.

Qualified Installing Agency

Installation and replacement of gas piping, gas utilization

equipment or accessories and repair and servicing of equipment

shall be performed only by a qualified agency. The term

“

qualified

agency

”

means any individual, firm, corporation or company

which either in person or through a representative is engaged

in and is responsible for (a) the installation or replacement of

gas piping or (b) the connection, installation, repair or servicing

of equipment, who is experienced in such work, familiar with all

precautions required and has complied with all the requirements

of the authority having jurisdiction.

Commonwealth of massachusetts: The installation must be

made by a licensed plumber or gas fitter in the Commonwealth

of massachusetts.

High Altitude (USA)

When installing this fireplace at an elevation above 2000 feet

(in the United States) it may be necessary to decrease the input

rating by changing the existing burner orifice to a smaller size.

Generally, input should be reduced 4 percent for each 1000

feet above sea level. However, if the heating value of the gas

has been reduced, this general rule may not apply. Check with

empire Comfort System’s local gas utility for proper orifice size

identification.

High Altitude (CANADA)

Altitude: 0-4500 feet (0-1370 m)

When installing this fireplace at an elevation above 4500 feet

(in Canada), check with local authorities.

Consult your local gas utility for assistance in determining the

proper orifice for your location.

HOMEOWNER REFERENCE INFORMATION

We recommend that you record the following information about your fireplace.

model Number:

_____________________________

Date purchased:

________________________

Serial Number:

_____________________________

Location of fireplace:

_____________________

Dealer Name:

______________________________

Dealer Phone:

_________________________

Notes:

______________________________________________________________________________

Содержание DVCT36CBP

















































Результаты поиска

Содержание DVCT36CBP

Отзывы:

Похожие инструкции для DVCT36CBP

Бренды по названию

Популярные бренды

Empire Comfort Systems DVCT36CBP, Руководство по установке

Результаты поиска

Содержание DVCT36CBP

Отзывы:

Похожие инструкции для DVCT36CBP

Бренды по названию

Популярные бренды