Empire Comfort Systems DVCT36CBP страница 43 Скачать руководство пользователя

Страница: 43 / 48

38745-4-0319

Page 43

Do NoT oPeRATe THIS APPLIANCe WITHoUT GLASS FRoNT PANeL INSTALLeD

Before enclosing the vent pipe assembly, operate the appliance to ensure it is venting properly.

• If this appliance is installed directly on carpeting,

tile or other combustible material other than

wood flooring the appliance shall be installed on

a metal or wood panel extending the full width

and depth of the appliance.

The base referred to above does not mean the

fireproof base as used on wood stoves. The

protection is for rugs that are extremely thick and

light colored tile.

• Children and adults should be alerted to the

hazards of high surface temperatures and should

stay away to avoid burns or clothing ignition.

• Young children should be carefully supervised

when they are in the same room as the appliance.

• Clothing or other flammable material should not

be placed on or near the appliance.

• Adequate accessibility clearances for servicing

and proper operation.

• This appliance must not share or be connected

to a flue serving a separate solid-fuel burning

appliance.

• Keep the area around your appliance clear

of combustible materials, gasoline and other

flammable vapor and liquids.

• Under no circumstances should any solid fuels

(wood, coal, paper or cardboard etc.) be used in

this appliance.

• The flow of combustion and ventilation air must

not be obstructed in any way.

• Young children should be carefully supervised

when they are in the same room as the appliance.

Toddlers, young children, and others may be

susceptible to accidental contact burns. A

physical barrier is recommended if there are at-

risk individuals in the house. To restrict access

to a fireplace or stove, install an adjustable safety

gate to keep toddlers young children, and other

at-risk individuals out of the room and away from

hot surfaces.

• A barrier designed to reduce the risk of burns

from the hot viewing glass is provided with this

appliance and shall be installed for the protection

of children and other at-risk individuals. barrier

required, but may be sold separately.

• If the barrier becomes damaged, the barrier shall

be replaced with the manufacturer’s barrier for

this appliance.

• Any safety screen, guard, or barrier removed for

servicing an appliance must be replaced prior to

operating the appliance.

• Due to high temperatures the appliance should

be located out of traffic and away from furniture

and draperies.

• The glass front or any part removed for servicing

the appliance must be replaced prior to operating

the appliance. Work should be done by a qualified

service person.

•  Keep burner and control compartment clean.
•  Vent cap is hot while fireplace is in operation.
•  Installation and repair should be done by a

QUALIFIED SERvICE PERSON. The appliance

should be inspected before use and at least

annually by a qualified service person. More

frequent cleaning may be required due to

excessive lint from carpeting, bedding materials,

etc. It is imperative that control compartments,

burners and circulating air passageways of the

appliance be kept clean.

• DO NOT put anything around the fireplace that

will obstruct the flow of ventilation air.

• Clearance in accordance with local installation

codes and the requirements of the gas supplier.

• DO

keep the appliance area clear and free

from combustible material, gasoline and other

flammable vapors and liquids.

• DO

examine venting system periodically and

replace damaged parts.

• DO

make a periodic visual check of pilot and

burners. Clean and replace damaged parts.

• CAUTION: The glass used in your fireplace

is tempered glass. If the glass is cracked or

damaged in any way, it should be replaced

only with a complete glass frame assembly

from Empire. See parts list on Pages

56 - 61 for

ordering.

• DO NOT use this fireplace if any part has been

under water. Immediately call a qualified service

technician to inspect the heater and to replace

any part of the control system and any gas

control which has been under water.

• Any safety screen or guard removed for servicing

an appliance must be replaced prior to operating

the appliance.

IMPORTANT SAFETY INFORMATION

Содержание DVCT36CBP

















































Результаты поиска

Содержание DVCT36CBP

Отзывы:

Похожие инструкции для DVCT36CBP

Бренды по названию

Популярные бренды

Empire Comfort Systems DVCT36CBP, Руководство по установке

Результаты поиска

Содержание DVCT36CBP

Отзывы:

Похожие инструкции для DVCT36CBP

Бренды по названию

Популярные бренды